Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-18-2016, 11:30 AM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by zeno View Post
If the pix is just dark but otherwise good & sharp with good
B&W try moving the G-2 ( a.k.a. screen ) control a little first.

G-2 is on CRT socket. Circuit simple, flyback pulse rectified by
D604 ( apx 300 VDC ) goes to one end of control. Other end
a 1 meg R681 to ground.
CRT pin 8 should be abt 250 VDC.

The 3 cathodes pins 1, 6, & 7 should be abt 75 V. if they
are much higher you have a video problem.

73 Zeno
I just wonder if the board has the low value 'lytic in the screen circuit, 10mfd @ 315vdc, that might be bad. I don't know if the cap is on the CRT board or on the main board.
Reply With Quote
  #2  
Old 02-18-2016, 12:06 PM
Captainclock Captainclock is offline
Banned
 
Join Date: Dec 2013
Location: Elkhart, Indiana
Posts: 1,189
Quote:
Originally Posted by dieseljeep View Post
I just wonder if the board has the low value 'lytic in the screen circuit, 10mfd @ 315vdc, that might be bad. I don't know if the cap is on the CRT board or on the main board.
I don't know either, what would the capacitor do exactly and what circuit would it be associated with? I'm asking because I could see if I could locate it by looking around on the different circuit boards for it.
Reply With Quote
  #3  
Old 02-18-2016, 07:51 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
The G-2 is on the CRT socket.

73 Zeno
Reply With Quote
  #4  
Old 02-18-2016, 09:04 PM
Captainclock Captainclock is offline
Banned
 
Join Date: Dec 2013
Location: Elkhart, Indiana
Posts: 1,189
Quote:
Originally Posted by zeno View Post
The G-2 is on the CRT socket.

73 Zeno
I see, well I looked there as well and I didn't see anything there I saw controls Marked RED, GREEN, and BLUE and there were 2 of them, When you say G-2 control are you referring to the second Green adjustment? Or is there another control on the CRT Socket Board that is actually marked G-2?

EDIT: Found the control you were talking about, it was marked "Screen" and it was on the bottom left hand corner of the CRT Board sitting at an angle. It definitely wasn't set right from the factory because I was able to set the control to the middle and I still had plenty of room to adjust yet before finally getting any retrace lines of any sort.I currently have it set in the middle and it gives a nice bright picture and plenty of adjustment room for the brightness control in the front. and it has probably the best picture I've seen on a portable color TV that size! Definitely a Low Hours TV Set! Sadly enough I couldn't get my camera to get a nice screen shot of the picture on the TV, it was nothing but bright light to the camera for some reason, it wasn't able to make out a discernable image on the screen.

Last edited by Captainclock; 02-18-2016 at 09:38 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:59 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.