Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-15-2015, 02:00 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
At this point, with the chassis still in fault mode, I would put an ohmmeter on the main B+ rail, to ground. A good place to find the B+ rail is the width coil or the top of filter caps C3A/C2B. (with the set off, of course.) Connect the positive lead to the B+ rail, negative lead to ground. What reading does it settle into after the initial charge-up spike?
Does it stop hard at a few K ohms, or drift up into the fractional-megohm range?

Last edited by old_coot88; 12-15-2015 at 04:57 PM.
Reply With Quote
  #2  
Old 12-17-2015, 01:37 PM
Kamakiri's Avatar
Kamakiri Kamakiri is offline
Administrator
 
Join Date: Jun 2002
Location: Buffalo, New York
Posts: 5,109
Quote:
Originally Posted by old_coot88 View Post
At this point, with the chassis still in fault mode, I would put an ohmmeter on the main B+ rail, to ground. A good place to find the B+ rail is the width coil or the top of filter caps C3A/C2B. (with the set off, of course.) Connect the positive lead to the B+ rail, negative lead to ground. What reading does it settle into after the initial charge-up spike?
Does it stop hard at a few K ohms, or drift up into the fractional-megohm range?
Voltage test didn't change with all 4 tubes removed, so I went on to this. The meter stopped at almost exactly 6.8 K Ohms.
__________________
"Restoring a tube TV is like going to war. A color one is like a land war in Asia."
Reply With Quote
  #3  
Old 12-17-2015, 03:45 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by Kamakiri View Post
Voltage test didn't change with all 4 tubes removed, so I went on to this. The meter stopped at almost exactly 6.8 K Ohms.
Well, 6.8K is reasonable enough, considering that the B+ bleeder string to ground (R127A and R128A) add up to 8.1K. Current will only be around 45 ma., nowhere near the 175 or so ma. that's going thru poor R127B.

It almost looks like a B+ filter cap is breaking down under voltage, like maybe a cap has been replaced with one having too low a voltage rating. The most likely suspect would be C4A, which should be 40 mf and rated at 450V. Does the C4 can show evidence of heating?

Last edited by old_coot88; 12-17-2015 at 03:54 PM.
Reply With Quote
  #4  
Old 12-20-2015, 01:15 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Any progress on this?

I'm curious how much your B+ increased when you pulled those 4 tubes? Or if it didn't, I'd continue to pull tubes, one at a time, except leave the audio output tube in. Continue to check voltage across R127B and B+. Make sure B+ doesn't exceed your 450v cap ratings while doing this.
Reply With Quote
  #5  
Old 12-20-2015, 01:32 PM
Kamakiri's Avatar
Kamakiri Kamakiri is offline
Administrator
 
Join Date: Jun 2002
Location: Buffalo, New York
Posts: 5,109
Quote:
Originally Posted by Kevin Kuehn View Post
Any progress on this?

I'm curious how much your B+ increased when you pulled those 4 tubes?
No change. With all those tubes out and still that much of a current draw, are there any likely suspects at this point?
__________________
"Restoring a tube TV is like going to war. A color one is like a land war in Asia."
Reply With Quote
Audiokarma
  #6  
Old 12-20-2015, 01:50 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
How bizarre. So with those tubes removed, what voltages do you measure across C1A,C3A and C1C? Measure directly across their + and - terminals, NOT from + to chassis.
Reply With Quote
  #7  
Old 12-20-2015, 01:30 PM
Kamakiri's Avatar
Kamakiri Kamakiri is offline
Administrator
 
Join Date: Jun 2002
Location: Buffalo, New York
Posts: 5,109
Quote:
Originally Posted by old_coot88 View Post
It almost looks like a B+ filter cap is breaking down under voltage, like maybe a cap has been replaced with one having too low a voltage rating. The most likely suspect would be C4A, which should be 40 mf and rated at 450V. Does the C4 can show evidence of heating?
C4's been replaced with all new Nichicons. C4A is now 47 uF @ 450v. Don't see any signs of anything under there.....
__________________
"Restoring a tube TV is like going to war. A color one is like a land war in Asia."
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:06 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.