Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-15-2015, 01:35 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Riders says 3.2 watts on the 6750 ohmer.

By having the one end of the 6750 ohm resistor not grounded, you introduced higher than normal voltages to some circuits(haven't looked at which yet). That may explain why some circuits were pulling more than their normal load.

Last edited by Kevin Kuehn; 12-15-2015 at 01:43 PM.
Reply With Quote
  #2  
Old 12-15-2015, 01:39 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
My next question- is the green wire end of the 12 ohm resistor connected to ground, so now you have both ends grounded? In other words, did you inadvertently connect the end to chassis ground that was suppose to be up on the 3 terminal from the left of the Candohm?
Reply With Quote
  #3  
Old 12-15-2015, 01:54 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Is it possible the other green wire you have going to the left end terminal of the Candohm, is also grounded, and that should be on the right end of the 6750 ohm section? It would make some sense that those two green wires disappear to a ground lug under the chassis. Sorry about so many details, but it's just a little confusing in that chimney.
Reply With Quote
  #4  
Old 12-15-2015, 02:05 PM
Kamakiri's Avatar
Kamakiri Kamakiri is offline
Administrator
 
Join Date: Jun 2002
Location: Buffalo, New York
Posts: 5,109
Quote:
Originally Posted by Kevin Kuehn View Post
Is it possible the other green wire you have going to the left end terminal of the Candohm, is also grounded, and that should be on the right end of the 6750 ohm section? It would make some sense that those two green wires disappear to a ground lug under the chassis. Sorry about so many details, but it's just a little confusing in that chimney.
Hah, you're tellin' me!

No, in effect for some reason (read brain fart) I didn't realize at a glance that the funky cloth covered little inchworm was a 12 watt resistor, so I added a 10 watt resistor where it should have gone according to the Sams, thereby giving that part of the circuit a 22 ohm resistance instead of 12.

Then, that 6750 ohm section should have had the inner terminal going to chassis ground, and I believe I just got confused working from the schematic alone.

I'll order up some parts tonight, and double check them against another 8TS30 I have here.
__________________
"Restoring a tube TV is like going to war. A color one is like a land war in Asia."
Reply With Quote
  #5  
Old 12-15-2015, 02:16 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by Kamakiri View Post
Hah, you're tellin' me!

No, in effect for some reason (read brain fart) I didn't realize at a glance that the funky cloth covered little inchworm was a 12 watt resistor, so I added a 10 watt resistor where it should have gone according to the Sams, thereby giving that part of the circuit a 22 ohm resistance instead of 12.

Then, that 6750 ohm section should have had the inner terminal going to chassis ground, and I believe I just got confused working from the schematic alone.

I'll order up some parts tonight, and double check them against another 8TS30 I have here.

OK, you posted while I was out looking for another reference photo. Sounds like you've now got your head screwed back on straight.
Reply With Quote
Audiokarma
  #6  
Old 12-15-2015, 02:12 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
I found this picture from another thread here. Looks like what I thought were green wires are not suppose to be grounds. Apparently the ground connections are to be soldered directly to the chassis below the chimney, as shown. Sorry for making things more confusing, I've never restored one of these RCA sets.

Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:06 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.