Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-05-2015, 03:04 PM
fixmeplease fixmeplease is offline
VideoKarma Member
 
Join Date: Apr 2015
Posts: 240
Im including a pic of that part of the schematic. It has a 5.6 ohm fuseable installed (R57) and that is fine. Its the other one (R58) that tests so high. I circled them in red.

Thanks again for the advise. I will recoat the CRT, clean sockets and tubes, put in new electros and see what happens. (maybe other things that I spot) All the tubes did light up when I had it powered, but several were bad so I will replace those too. I guess I will just put it all back together before trying it. It wasnt t too bad to take out, I just worry about the neck.

Edit: electric M, I posted before seeing your last post. I dont mind switching the caps if I need too. They are all bumble bees so I figured there may be bad ones anyway.
Attached Images
File Type: jpg 005.jpg (78.1 KB, 28 views)
Reply With Quote
  #2  
Old 12-05-2015, 03:10 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
You could probably get away with gluing aluminum foil to the glass to replace the flaking stuff. Avoid the high voltage connection and the yoke area. And be sure the foil is connected to the set's ground.


You'll need to replace the usual wax caps, bumblebees and electrolytics.
__________________
Reply With Quote
  #3  
Old 12-05-2015, 07:30 PM
fixmeplease fixmeplease is offline
VideoKarma Member
 
Join Date: Apr 2015
Posts: 240
Being a rookie on tv's, I probably better not try the tin foil as I may damage something or do it wrong. I painted for a living many years and understand that. Is this the correct slip plate product? There are a couple varieties and this one has a G on the end. http://www.ebay.com/itm/SLIP-PLATE-3...4AAOSwnipWYodd

At the very least, I'll test the bumble bees and replace the bad ones, after it being suggested now a couple times. Maybe I'll just do them all as its good experience anyways. Thanks!
Reply With Quote
  #4  
Old 12-05-2015, 07:39 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by fixmeplease View Post

At the very least, I'll test the bumble bees and replace the bad ones, after it being suggested now a couple times. Maybe I'll just do them all as its good experience anyways. Thanks!
Don't bother testing them, they're all bad.
__________________
Reply With Quote
  #5  
Old 12-05-2015, 08:05 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
It may be an error in Sams. If its a say 33 ohm & you add
a zero its a 330 ohm..........

For now just check for APX 95 vac on pin 7 of tube V7.
You do not want to put a 33 ohm in if its a 330 ohm.
NOT good for the filaments............

Why get a pix first ?
1) to be sure you got a good CRT. Even if it tests good it still can be bad
& visa versa.
2) check to see that all MAJOR parts are OK. Even 40 yrs ago
you couldnt get some of this stuff.
3) you learn by troubleshooting NOT shot-gunning
4)re-caps need to be done a few at a time followed by a test.
If you do something wrong its easier to find if you just gotta
look at a few things. Nothing worse than finding a self induced
problem. Sends techs running if its "been somewhere else"
& never fixed. And you never get the truth out of the
customer !!

good luck
Zeno
Reply With Quote
Audiokarma
  #6  
Old 12-05-2015, 08:41 PM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by zeno View Post
It may be an error in Sams. If its a say 33 ohm & you add
a zero its a 330 ohm..........

For now just check for APX 95 vac on pin 7 of tube V7.
You do not want to put a 33 ohm in if its a 330 ohm.
NOT good for the filaments............

Why get a pix first ?
1) to be sure you got a good CRT. Even if it tests good it still can be bad
& visa versa.
2) check to see that all MAJOR parts are OK. Even 40 yrs ago
you couldnt get some of this stuff.
3) you learn by troubleshooting NOT shot-gunning
4)re-caps need to be done a few at a time followed by a test.
If you do something wrong its easier to find if you just gotta
look at a few things. Nothing worse than finding a self induced
problem. Sends techs running if its "been somewhere else"
& never fixed. And you never get the truth out of the
customer !!

good luck
Zeno
33 or 36ohms has to be right! 36 ohmsX 600ma=21.6 drop. 21.6+95=117volts, approx.
Reply With Quote
  #7  
Old 12-06-2015, 03:24 PM
Paul Knaack Paul Knaack is offline
VideoKarma Member
 
Join Date: Jul 2013
Location: Dale Wi.
Posts: 281
Quote:
Originally Posted by dieseljeep View Post
33 or 36ohms has to be right! 36 ohmsX 600ma=21.6 drop. 21.6+95=117volts, approx.
330 ohms at .6 amps would drop 198 volts
Reply With Quote
  #8  
Old 12-06-2015, 12:07 PM
Marco-nix's Avatar
Marco-nix Marco-nix is offline
VideoKarma Member
 
Join Date: Apr 2014
Location: somewhere on earth
Posts: 305
Quote:
Originally Posted by zeno View Post
It may be an error in Sams. If its a say 33 ohm & you add
a zero its a 330 ohm..........Zeno



You are right. Over my schematic reading, I realized that publications from SAMS are often wrong. So now I am wary of what there are sometimes in the schemas. nothing better than a regular of repair of TVs to give you the real stuff, the real values of each piece...
Reply With Quote
  #9  
Old 12-06-2015, 12:17 PM
fixmeplease fixmeplease is offline
VideoKarma Member
 
Join Date: Apr 2015
Posts: 240
I couldnt read the resistor well until I took pictures of it, then it shows them fairly well except for the last number. Top row A43(K or X) 402. Bottom is W.G.33 and the last one could be a 4. You may be correct about the sam being wrong. It tested at 356 this morning with a DVM. So for now Im guessing i should use it?
I'll order the coating product mentioned. Thanks again!
Attached Images
File Type: jpg 035.jpg (80.9 KB, 17 views)
Reply With Quote
  #10  
Old 12-06-2015, 01:19 PM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by fixmeplease View Post
I couldnt read the resistor well until I took pictures of it, then it shows them fairly well except for the last number. Top row A43(K or X) 402. Bottom is W.G.33 and the last one could be a 4. You may be correct about the sam being wrong. It tested at 356 this morning with a DVM. So for now Im guessing i should use it?
I'll order the coating product mentioned. Thanks again!
I looked the schematic in Beitmans. The heater string is the same as in Sams, showing a 36 ohm, 20 resistor. Ohm's law proves that the resistor has to be a value between 30 and 40 ohms, otherwise the tubes wouldn't lite at all.
Is your meter auto-ranging or it doesn't display the decimal point.
Your earlier posts, mentioned that the tubes lit, when you brought it up on line, but all you got was a squeal, which indicated possible bad electrolytics.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:28 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.