Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-17-2015, 03:45 PM
timmy's Avatar
timmy timmy is offline
VideoKarma Member
 
Join Date: Jan 2011
Location: Delaware ny
Posts: 3,719
The hv tripler would make the hv in place of the secondary, donut while yes the primary stayed intact. I think someone here on karma already posted that that very thing was done but don't remember who, it was awhile ago. There has to be a simpler why other then rewinding a primary not to mention a secondary, donut.
Reply With Quote
  #2  
Old 10-17-2015, 08:56 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by timmy View Post
The hv tripler would make the hv in place of the secondary, donut while yes the primary stayed intact. I think someone here on karma already posted that that very thing was done but don't remember who, it was awhile ago. There has to be a simpler way other than rewinding a primary not to mention a secondary, donut.
You're probably referring to this thread, where a fella in England describes how he replaced a HV winding with a tripler (although in a B&W set).
See post# 18.
http://videokarma.org/showthread.php...winding+flyack

Some translations of terms would probably help:
'Overwind' = HV secondary, 'donut', 'tire'
'EHT' (Extreme High Tension) = HV to CRT anode
'LOPT' (Line Output transformer) = Flyback xfmr.
'Line Output Valve' = Horiz. output tube

Note that he had to add some capacitance to the primary to compensate for the capacitance lost due to the missing 'donut'.

Earlier posts in the thread describe the perils and pitfalls one would encounter trying to actually rewind a flyback.
Reply With Quote
  #3  
Old 10-17-2015, 10:24 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
It would be nice to have some concrete results - all I'm hearing is "I believe," "I think" and "I've heard"...

A schematic of the mod, a screenshot, and a narrative would be nice.

I have dug out bad HV rectifiers from potted flybacks ('twas nice to have a dentist office next door with an underused Xray machine) and I've seen an doubler added to generate HV in a Conrac color monitor with a bad (internal arcing) potted doubler. That one was in an ATE station aboard the USS Theodore Roosevelt and our NDI shop Chief did the Xraying. We used a doubler originally used in a Xerox machine, after first frying a Tektronix doubler from an oscilloscope - it didn't have the current capability. The arcing caused tearing of the raster, and with text being the primary display, it made it unusable.

To try a tripler in a tube RCA with the usual 6JE6, 6DW4, and 6BK4C would be problematic - coming off the plate of the 6JE6 would provide HV only - no horizontal sweep, and coming off the top end of the primary would add capacitance ( a tripler is all caps and diodes, with a possible resistor if a focus tap is provided) - you might be able to use a doubler in lieu of a HV rectifier if the HV is low, but regulation might cause issues - shunting a doubler would take a bit more current through the 6BK4C, and I dunno what that might do. A donut swap from a good flyback might work, but I've never seen two RCA flybacks with the same donut (PRI/SEC) schematic - I'll post the Thordarson schematics to show what I see...

RCA flybacks, as some have mentioned, provide much more than just HV - they provide Horizontal sweep to the yoke, focus voltage, sync pulses to the Chroma circuits, and convergence signals for the set. True they all operate at 15,750 Hz or so, but inductances, winding counts, and resistances all differ, making it all but impossible to easily swap out.
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #4  
Old 10-17-2015, 10:30 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Seems like Tom Albrecht was experimenting with triplers, in a Philco projection set for one. Seems like he tried one in a color set too, but I can't recall the details.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:07 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.