Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-12-2015, 08:33 PM
MRX37 MRX37 is offline
VideoKarma Member
 
Join Date: Aug 2005
Posts: 1,579
Lets try and simplify this, well, for me anyway. I'm still very new to tube electronics, and I'm learning as I go. Please bear with me.

Now that I have a decent camera again, here's a full, high resolution shot of the chassis:
http://imgur.com/JFDq0nP

If you'd be kind enough to point out where I need to put my meter leads, and maybe some other areas where I should test voltages, that'll cut down on the number of stupid questions on my end.
Reply With Quote
  #2  
Old 10-12-2015, 09:06 PM
rca2000's Avatar
rca2000 rca2000 is offline
VideoKarma Member
 
Join Date: Mar 2003
Location: cincinnati,ohio
Posts: 2,090
See if you can show the TOP of the chassis for me....it will help me to figure it out better.

So far...I THINK...I see where you need to check. Looks like the main filter cap is on the extreme right....partially under the bottom of the cabinet. I only see a BIT of it...and need to see the TOP of the chassis, to tell if there are MORE caps...that need to be checked.

Scratch that....I checked an earlier post...and now see the chassis.

Last edited by rca2000; 10-12-2015 at 09:09 PM. Reason: more info.
Reply With Quote
  #3  
Old 10-12-2015, 09:23 PM
rca2000's Avatar
rca2000 rca2000 is offline
VideoKarma Member
 
Join Date: Mar 2003
Location: cincinnati,ohio
Posts: 2,090
Looking at the chassis tube layout...I see where you need to check for B+. You can either reach it on TOP of the chassis or UNDER It.

Next to the H-put tube...is a terminal strip. The THIRD terminal post is B+. CHeck this to GROUND...and see what it reads. you can ALSO measure this under the chassis, the third termnal is under that black capacitor.

I see what look like a diode under the chassis. It is under that red cap...above the brown tubualr cap--which is likely one of the doubler caps....ASSUMING...this set uses a doubler. The other doubler cap is likely part of the can cap on the right of the chassis.


IF this is a doubler power supply...you should have at least 275-285 volts B+ If NOT a doubler....only 140-150 volts.
Reply With Quote
  #4  
Old 10-12-2015, 09:28 PM
rca2000's Avatar
rca2000 rca2000 is offline
VideoKarma Member
 
Join Date: Mar 2003
Location: cincinnati,ohio
Posts: 2,090
And as others have said....do NOT measure the "Boot' or Boost voltage...UNLESS you have a meter than can read 1KV or so....it could eb that high. Measure ONLY the b+ right now..I suspect it is LOW....from your symptoms..
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:57 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.