Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-15-2015, 10:09 AM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
I've done this numerous times. But there's a caveat. It's always been on the standard layout with the damper in series with the B+ line going to the flyback.
I never did it on a pre-standardization layout where the damper is not in series. Your porthole is probably pre-standardization, so it might not work. Probably wouldn't hurt to try, though.

Try a disc cap of around 47pf - 82pf @4KV.

A quick check of the schematic will tell if it's a series layout or not.

(EDIT.) Have you checked the G2 (screengrid) voltage on the H out tube? If it's low it'll cause reduced width and HV.

Last edited by old_coot88; 09-15-2015 at 10:17 AM.
Reply With Quote
  #2  
Old 09-15-2015, 03:05 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by old_coot88 View Post
I've done this numerous times. But there's a caveat. It's always been on the standard layout with the damper in series with the B+ line going to the flyback.
I never did it on a pre-standardization layout where the damper is not in series. Your porthole is probably pre-standardization, so it might not work. Probably wouldn't hurt to try, though.

Try a disc cap of around 47pf - 82pf @4KV.

A quick check of the schematic will tell if it's a series layout or not.

(EDIT.) Have you checked the G2 (screengrid) voltage on the H out tube? If it's low it'll cause reduced width and HV.
Tim,

In your package, along with the cookie, is a bag with some 4KV caps - 100, 130, 160 and 220pf - I was gonna send a PM about them but saw this. I remember we used a 100pf cap in some sets, but I couldn't remember the range of values, and it is probably 47-100pF, so I erred on the wrong (high)side. Hopefully all you need is the cookie.

I see the flyback has been changed. FLy 52 and 53 (thordarson spec'd two flys for the PH's, not sure of Merit or Ram) are different animals, and it wouldn't be the first time someone (not you) changed a Flyback and used the wrong replacement. I have - on a Sony multi-system, and horizontal linearity was off - I adjusted to get it normal, and then had reduced width. So I called Sony, and they confirmed that I had the wrong fly, my mistake, and costly at that. Thankfully the set belonged to a good friend, so I didn't mind the lesson.

On a side, the ETF museum has two flys for Zenith PH's listed on their website...

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #3  
Old 09-15-2015, 03:08 PM
bigaudioal's Avatar
bigaudioal bigaudioal is offline
VideoKarma Member
 
Join Date: Mar 2012
Location: Gaithersburg, MD
Posts: 623
Quote:
Originally Posted by Findm-Keepm View Post
Tim,

In your package, along with the cookie, is a bag with some 4KV caps - 100, 130, 160 and 220pf - I was gonna send a PM about them but saw this. I remember we used a 100pf cap in some sets, but I couldn't remember the range of values, and it is probably 47-100pF, so I erred on the wrong (high)side. Hopefully all you need is the cookie.

Has the fly ever been changed? FLy 52 and 53 (thordarson spec'd flys for the PH's) are different animals, and it wouldn't be the first time someone (not you) changed a Flyback and used the wrong replacement. I have - on a Sony multi-system, and horizontal linearity was off - I adjusted to get it normal, and then had reduced width. So I called Sony, and they confirmed that I had the wrong fly, my mistake, and costly at that. Thankfully the set belonged to a good friend, so I didn't mind the lesson.

Cheers,
Fly was replaced with a Merit HVO-11, which listed this chassis (23G22) in it's literature that was in the box with it as an exact replacement.
__________________
-Al
Reply With Quote
  #4  
Old 09-16-2015, 12:55 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by bigaudioal View Post
Fly was replaced with a Merit HVO-11, which listed this chassis (23G22) in it's literature that was in the box with it as an exact replacement.
What was the original Zenith Fly? It'll start with an "S" - most of the Portholes used the Merit HVO-53, with some windings not used on some models.
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!

Last edited by Findm-Keepm; 06-19-2017 at 03:10 PM.
Reply With Quote
  #5  
Old 09-16-2015, 01:45 PM
bigaudioal's Avatar
bigaudioal bigaudioal is offline
VideoKarma Member
 
Join Date: Mar 2012
Location: Gaithersburg, MD
Posts: 623
Quote:
Originally Posted by Findm-Keepm View Post
What was the original Zenith Fly? It'll start with an "S" - most of the Portholes used the Merit HVO-53, with some windings not used on some models.
Original flyback was Zenith S-16204. On your attachment it says replacement should be Merit HVO-53 (3). What does the "(3)" indicate? Assuming it is a reference to a footnote. What does the footnote say?

I cross referenced S-16204 to Merit HVO-11. When I got the part, the original paperwork was inside (got it from Moyer in PA). Below are two photos of that paperwork. Showing it is a HVO-11 and showing that it replaces S-16204 out of the 23G22 chassis. So not sure if one is wrong, or both are right, etc??? Interestingly, all the S-numbered Zenith flys on the HVO-11 paperwork cross to the HVO-53 on your paperwork.

Wonder if the HVO-11 was a no good replacement in these models and updated to the HVO-53 later??? Anyone have any insights?

Thx.
Attached Images
File Type: jpg FullSizeRender1.jpg (89.0 KB, 14 views)
File Type: jpg FullSizeRender.jpg (62.5 KB, 13 views)
__________________
-Al

Last edited by bigaudioal; 09-16-2015 at 01:53 PM.
Reply With Quote
Audiokarma
  #6  
Old 09-16-2015, 02:14 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
The (3) indicates that the installer should use the inclosed sheet for instructions. Merit apparently consolidated their flybacks for the PortHoles into one number, unlike Thordarson, who kept it between FLY 52 and 53.

With the Merit HVO-53, there are several sets of windings, and you use only the ones for your set.

Thordarson lists one flyback for your model number, and another flyback for the chassis:

For Chassis 23G22 (and 23G23), use a Fly 53 to replace a S-16204

For Model G2346R (and G2346RZ), use a Fly 52 to replace a S-16566

They show the early PH's as using the 52, and the later chassis using the 53.

Dunno why the discrepancy - anyone have a Zenith 23G22 parts list? Going by model is sketchy, it appears.

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #7  
Old 09-16-2015, 06:56 PM
bigaudioal's Avatar
bigaudioal bigaudioal is offline
VideoKarma Member
 
Join Date: Mar 2012
Location: Gaithersburg, MD
Posts: 623
There is a parts list for the 23G22 chassis in the Zenith Manual I posted the link to earlier in this thread, isn't there? From the ETF site.
__________________
-Al
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:13 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.