Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-17-2015, 07:44 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Retro-guy View Post
Okay I did some searching

I think I have A CONDITION CALLED blooming which causes the raster to expand by 10 % if I turn the brightness up,loses focus in middle to,which it does and is caused by poorly regulated EHT ??

Also when I clunk thru the channels the dim spot goes away and the tube is flashing very bright so I know its a good tube,which means either poorly regulated EHT,B+ maybe...someone mentioned to me that
the B+ that goes to vertical deflection,that the fault might be there ??

Which means if poor regulated EHT ,would cause the tube to not operate at its fullest and I could have a much brighter tube if the things driving it would work properly :d




I just tried it with a 68.000 pf cap which is more then enough in the place of the 56.000 pf but results are pretty much same ...
Most monochrome sets lacked any HV regulation circuitry, And 'HV regulation' (more like HV sag) were usually caused by excessive load on the HV circuit, or the horizontal deflection system being miss-adjusted or having defective parts.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #2  
Old 02-17-2015, 07:52 PM
Retro-guy Retro-guy is offline
VideoKarma Member
 
Join Date: Feb 2015
Posts: 26
Yea I made a machine that helped me to unwound it and at same time count the turns and length of wire.., very handy


Ive used some kind of special tape for insulation between layers that I got from a guy who re-wounds motors and the flyback seems to be working GOOD ,no shorts/overheating/smoking so the hard part seems to be over

You can see from pics I stripped it completely down ...
But this dim spot and blooming,poorly regulated EHT is bothering me quite HARD


Quote:
Originally Posted by Electronic M View Post
Most monochrome sets lacked any HV regulation circuitry, And 'HV regulation' (more like HV sag) were usually caused by excessive load on the HV circuit, or the horizontal deflection system being miss-adjusted or having defective parts.
well maybe just a little but IF I turn the brightness close to max the dim spot gets even more visible and the focus goes away(raster stretches for about 10%),gonna take some voltages tomorrow and put a signal into it
and then well see where we are ...
Attached Images
File Type: jpg IMG1625.jpg (58.3 KB, 28 views)
File Type: jpg IMG1766.jpg (41.9 KB, 25 views)
File Type: jpg IMG1765.jpg (44.7 KB, 27 views)
File Type: jpg IMG1770.jpg (53.6 KB, 27 views)
File Type: jpg IMG1771.jpg (51.9 KB, 30 views)

Last edited by Retro-guy; 02-17-2015 at 07:57 PM.
Reply With Quote
  #3  
Old 02-17-2015, 09:53 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Have you substituted the HV (EHT) rectifier tube? It is the most frequent cause of blooming.

Even if it tests 'good' on a tester, it can still fail in operation. The only valid test is subbing with a known good tube.
Reply With Quote
  #4  
Old 02-18-2015, 01:23 PM
Retro-guy Retro-guy is offline
VideoKarma Member
 
Join Date: Feb 2015
Posts: 26
Quote:
Originally Posted by old_coot88 View Post
Have you substituted the HV (EHT) rectifier tube? It is the most frequent cause of blooming.

Even if it tests 'good' on a tester, it can still fail in operation. The only valid test is subbing with a known good tube.

Well at this moment I don't have a spare one but the DY87 in the set seems to be OK ALMOST LOOKS LIKE NEW ...


it probably has bad EHT regulation,what components can I check ???
Also where can I found some lecture on how these things work,so I would know a bit more what I'm doing ??
Attached Images
File Type: jpg IMG1778.jpg (53.0 KB, 19 views)
Reply With Quote
  #5  
Old 02-18-2015, 04:06 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by Retro-guy View Post
Well at this moment I don't have a spare one but the DY87 in the set seems to be OK ALMOST LOOKS LIKE NEW ...


it probably has bad EHT regulation,what components can I check ???
Also where can I found some lecture on how these things work,so I would know a bit more what I'm doing ??
A tube can LOOK PERFECT and BE COMPLETELY DEAD....However if it looks dead (white getter, hole or crack in the glass, etc) it is dead. The only sure test of an HV rectifier is to get another HV rectifier and try it in the set. No tube tester made comes close to testing HV rectifiers under real world application conditions.

Also there is almost certainly NO HV regulation circuit in that set. Usually they design the horizontal deflection system, flyback, and HV rectifier system to produce varying, but acceptably varying HV output. However if the HV/horizontal deflection system is loaded beyond design (as I suspect yours is on the edge of, since increasing the brightness pushes it over the edge), or the oscillator/output is not preforming correctly it will vary outside the acceptable range.

There have not been lectures on this subject in decades. You can find some TV troubleshooting videos on youtube (Banderson has many good videos) which may be helpful, but you are best off getting some TV servicing books off the internet, and reading them. Also google searching this forrum and others like it will dig up some good info on horizontal troubleshooting. Unless you can find someone with the same set and issue the info will be general, and possibly not completely apply to your set.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
Audiokarma
  #6  
Old 02-18-2015, 05:37 PM
Retro-guy Retro-guy is offline
VideoKarma Member
 
Join Date: Feb 2015
Posts: 26
Okay gonna try a different DY87 ...

Also a new problem has developed,I only have a raster now,the snow disappeared,but I know the tuners work cause I have perfect sound only
picture went away ,only white raster ,when I measured the voltage on the cathode of the CRT was only 14 V which is a bit low and pin 6 had 12 v instead of 80v and pin 9 had 260V instead of 210V

there is something weird going on in this TV ...
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:02 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.