Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-08-2015, 10:25 AM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by Zenith6S321 View Post
Here is a picture of the SAMs IF frequency response. Figure 1 is the third IF and figure 2 is the first and second response. The next picture shows the third IF response is pretty close to what SAMs shows (you have flip the plot horizontally to match my scope). The next picture is what I got for the first and second IF response. Its way off. The response at the 45.75 MHz marker shown should be much lower amplitude. Following SAMs alignment I tried to adjust A6, the 41.25 MHz trap and found it very hard to turn because its core was coming apart. I pulled the chassis, removed the coil, and removed the core. One end had two small pieces broken off. I tried a shorter ferrite core to see if the coil form was too tight. It was very tight. I ended up finding that a 1/4"-28 tap matches this ferrite core. So I tapped the coil form as shown in the next picture. The last picture shows the shavings removed from the coil form. The small ferrite core now threads nicely though the core. I am trying to glue the two small ferrite pieces back onto the broken core. If they hold, I will invert the core so that the broken pieces will be at the end that is not usually used for adjusting. Anyone know of a place to buy 1/4" threaded ferrite cores?

Dave
I've got a bunch (~ half of a cigar box full) of ferrite cores - how long?

I always pulled the cores from sets I junked - and at my dad's shop, I was the TV stripper/parts puller/gofer. I probably have junked over 300 sets in 30+ years. First we saved everything, then just certain chassis, then just modules, and finally, only good chassis/CRTs. My user name comes from my attitude - if you find it, keep it. Someone, somewhere will likely need it.

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #2  
Old 02-08-2015, 05:47 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
Quote:
Originally Posted by Findm-Keepm View Post
I've got a bunch (~ half of a cigar box full) of ferrite cores - how long?

I always pulled the cores from sets I junked - and at my dad's shop, I was the TV stripper/parts puller/gofer. I probably have junked over 300 sets in 30+ years. First we saved everything, then just certain chassis, then just modules, and finally, only good chassis/CRTs. My user name comes from my attitude - if you find it, keep it. Someone, somewhere will likely need it.

Cheers,
Nice. All I could find online were ferrite interference filter beads. I need two 1/4" by 5/8" long cores. If you have them, let me know the cost and shipping charges. Thanks.

Dave
Reply With Quote
  #3  
Old 02-10-2015, 08:13 AM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by Zenith6S321 View Post
Nice. All I could find online were ferrite interference filter beads. I need two 1/4" by 5/8" long cores. If you have them, let me know the cost and shipping charges. Thanks.

Dave
PM sent.
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #4  
Old 02-10-2015, 07:18 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
Quote:
Originally Posted by Findm-Keepm View Post
PM sent.
Thanks very much for your kind help!

Dave
Reply With Quote
  #5  
Old 02-10-2015, 07:40 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
I put my glued together ferrite core back in its coil and put the set back together. Then I tried using the Sams IF alignment procedure. It did help some. The Sams procedure tells you to use a demodulator probe at points after the detector. This did not work for me. I used a normal scope probe and got reasonable waveforms. The Sams also shows three IF sweep curves but the alignment text only refers to two of them. After the Sams alignment procedure I did get rid of the ringing in the video but also lost color. I could not match the curves response in the 42-43 MHz range. I used the VA62 multi-burst and tweaked the IF adjustments to get more color signal frequencies through (3 to 4 MHz) and got the color back. But when looking at a channel 3 RF signal I got a noisy picture.

I looked through the R.L. Goodman Zenith Color TV service manual and found a more detailed IF alignment than the Sams. It showed similar sweep curves but its procedure referred to all of them. So my next attempt will be to use this alignment procedure. The procedure is general to cover several Zenith sets, including the 27KC20 (which has very similar design and is the successor to my 29JC20), so some test point designations require translation to use on my set. I am no whiz at aligning sets, but I am determined.

Dave
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:39 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.