Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-01-2015, 10:58 PM
miniman82's Avatar
miniman82 miniman82 is offline
First Light: 1952-2011
 
Join Date: Jun 2009
Location: Great Mills, MD
Posts: 4,183
Looks like a decent pic already, I think you'll find the ghosting is an IF/tuner issue. Probably alignment time.
__________________
Evolution...
Reply With Quote
  #2  
Old 02-01-2015, 11:09 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
I wonder if a Velcro strap wrapped around that cloverleaf would hold it in place?
Reply With Quote
  #3  
Old 02-03-2015, 07:07 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
Quote:
Originally Posted by Kevin Kuehn View Post
I wonder if a Velcro strap wrapped around that cloverleaf would hold it in place?
That would help firm up the angles between the pole pieces. I also see that the green is titled back some. Maybe I need a ring of plastic to hold then in the same plane.

Dave
Reply With Quote
  #4  
Old 02-04-2015, 12:32 AM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Before even thinking of messing with alignment, try subbing the last IF tube. It can cause ringing that can be mistaken for misalignment.

On that stripped gear, your shrink tubing collar is a good idea in addition to epoxy. "Belt and suspenders" redundancy.

Last edited by old_coot88; 02-04-2015 at 12:35 AM.
Reply With Quote
  #5  
Old 02-04-2015, 09:13 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
Quote:
Originally Posted by old_coot88 View Post
Before even thinking of messing with alignment, try subbing the last IF tube. It can cause ringing that can be mistaken for misalignment.

On that stripped gear, your shrink tubing collar is a good idea in addition to epoxy. "Belt and suspenders" redundancy.
I tried changing each and all of the three IF tubes with some change to the ringing. Three new tubes in place of the originals does have a bit less ringing. I will try an alignment this weekend.

I'm gonna add the epoxy to the gear too.

Dave
Reply With Quote
Audiokarma
  #6  
Old 02-04-2015, 09:41 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Quote:
Originally Posted by Zenith6S321 View Post
I tried changing each and all of the three IF tubes with some change to the ringing. Three new tubes in place of the originals does have a bit less ringing. I will try an alignment this weekend.

I'm gonna add the epoxy to the gear too.

Dave
I found that all of the Zenith color roundie convergence coils are interchangeable. The latter ones might not aesthetically correct but at least they are better made and more rugged.

The epoxy trick would not fix the broken fine tuning gear on my Zenith. The reason was that the plastic appeared to have shrunk and epoxying it would have left a considerable gap between teeth at the break. What I did was to cut an O from the end of a BIC pen, the inner diameter of which was roughly equal or slightly smaller than the gear when compressed to close the gap. With the fine tuning shaft removed, I heated it with a large soldering iron until it would just begin to melt the gear and then with gear compressed around the shaft, I slipped on the BIC ring to hold the gear compressed.

Fix ensured the gear melted into the splines and there would be no gap between the teeth where the break was. It was bit fiddley to fabricate and install, but the result worked like a charm.
Reply With Quote
  #7  
Old 02-04-2015, 09:36 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
maybe some delay line ringing?
Reply With Quote
  #8  
Old 02-04-2015, 10:31 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
Quote:
Originally Posted by DaveWM View Post
maybe some delay line ringing?
I just tried adjusting the delay line termination potentiometer. It did not affect this ringing.

Post #44 shows pictures of test pattern video driven into the first IF showing ringing and then composite video driven into just after the video detector that does not show nearly as much ringing. Sure seems like it's in the IF stages.

Dave
Reply With Quote
  #9  
Old 02-04-2015, 10:40 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
oh my yes, I missed that. I wonder if all the little ferrite beads are in place etc. on the filament leads? My later zenith (24MC32) has several IIRC on the IF filaments. Mine also has a 22k resistor across the secondary of the IF before the 3rd IF tube. Wonder if maybe that has drifted high? I assume its there to damp out oscillation.
Reply With Quote
  #10  
Old 02-07-2015, 06:46 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
Quote:
Originally Posted by DaveWM View Post
oh my yes, I missed that. I wonder if all the little ferrite beads are in place etc. on the filament leads? My later zenith (24MC32) has several IIRC on the IF filaments. Mine also has a 22k resistor across the secondary of the IF before the 3rd IF tube. Wonder if maybe that has drifted high? I assume its there to damp out oscillation.
My first two IF stages filaments have a ferrite bead, as well as a couple more beads in the filaments some color circuit tubes. I did check and replace out of tolerance resistors in the IF stages, being careful to match lead dress as close to original as possible.
Reply With Quote
Audiokarma
  #11  
Old 02-15-2015, 11:40 PM
damen's Avatar
damen damen is offline
VideoKarma Member
 
Join Date: Feb 2008
Location: Portland, OR
Posts: 673
Your 29JC is looking good. I have the manual scanned for it I could send you a link to if you don't have it. Just PM Me.
Attached Images
File Type: jpg scan.jpg (65.5 KB, 26 views)
Reply With Quote
  #12  
Old 02-16-2015, 12:24 AM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Quote:
Originally Posted by damen View Post
Your 29JC is looking good. I have the manual scanned for it I could send you a link to if you don't have it. Just PM Me.
I'd be interested in a copy too.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #13  
Old 02-16-2015, 11:01 AM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
Quote:
Originally Posted by damen View Post
Your 29JC is looking good. I have the manual scanned for it I could send you a link to if you don't have it. Just PM Me.
Wow, cool! PM sent.

Dave
Reply With Quote
  #14  
Old 02-16-2015, 08:08 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
I took my centering rings out and re-glued them. Here are some pictures. There is a plastic ring at the end of the centering strings. The plastic rings are glued to the magnetic rings. The glue on mine had failed. I used some epoxy to glue them back on. There is a spacer between the magnetic rings and thick paper ring with tabs that holds them in place. The centering strings now work fine.
Attached Images
File Type: jpg Yoke-Centering-Rings-5.jpg (113.7 KB, 21 views)
File Type: jpg Yoke-Centering-Rings-4.jpg (122.0 KB, 19 views)
File Type: jpg Yoke-Centering-Rings-3.jpg (118.3 KB, 22 views)
File Type: jpg Yoke-Centering-Rings-2.jpg (125.9 KB, 18 views)
File Type: jpg Yoke-Centering-Rings.jpg (116.8 KB, 24 views)
Reply With Quote
  #15  
Old 02-20-2015, 08:26 PM
Zenith6S321's Avatar
Zenith6S321 Zenith6S321 is offline
VideoKarma Member
 
Join Date: Aug 2010
Location: Charleston, West Virginia
Posts: 303
I went through the chroma alignment. Only one adjustment needed tweaking. The set came without chassis hold-down bolts so I bought some that seem to do the job ok. I bolted the chassis and tuner in. About half of the plastic knobs snapped in half when I originally tried to pull them off. I used some epoxy for plastics and with some fiddling got them back on. I had to substitute an old knob for the color level control as it was missing. The UHF numbered dial indicator knob is missing. I only plan on using channels 3 or 4 but I'll keep an eye out for one if I can find a picture of what it looks like. I went through purity and convergence again. I still need to come up with a way to hold convergence pole pieces in alignment over the guns. Next I'm going to make mounting plate for a fan to get cool air into the HV cage. I plan to remove the rivet the access cover pivots on, remove it, and screw the fan plate in its place.
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:22 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.