Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Vintage TV & Radio Tech Forum

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-01-2015, 09:25 AM
stusnyder's Avatar
stusnyder stusnyder is offline
VideoKarma Member
 
Join Date: Nov 2010
Location: northeast Pa
Posts: 486
checked the vertical output, vertical osc. and agc section. Did not find anything significant... But I did find a new problem. I decided to check voltages, and I started at the power supply. There are 3 tubes in the supply, a 5y3gt, 5u4g, and a 6bf5.
So here's what I found:

5y3gt pin 2 riders says 187 volts. I got 218 volts.
5u4g pin 2 riders - 382 volts. I got 415
6bf5 pin 6 riders - 97 volts. I got 137.

My line voltage is 116 volts. Anyone have any ideas?
Reply With Quote
  #2  
Old 02-01-2015, 06:56 PM
init4fun's Avatar
init4fun init4fun is offline
VideoKarma Member
 
Join Date: Mar 2011
Posts: 1,210
Quote:
Originally Posted by stusnyder View Post
checked the vertical output, vertical osc. and agc section. Did not find anything significant... But I did find a new problem. I decided to check voltages, and I started at the power supply. There are 3 tubes in the supply, a 5y3gt, 5u4g, and a 6bf5.
So here's what I found:

5y3gt pin 2 riders says 187 volts. I got 218 volts.
5u4g pin 2 riders - 382 volts. I got 415
6bf5 pin 6 riders - 97 volts. I got 137.

My line voltage is 116 volts. Anyone have any ideas?
Are you using a modern digital volt meter to take these measurements ?

If so , your readings look fine . If you have a good ol Simpson 260 or other such vintage meter around , I'll bet you find the readings will more closely resemble spec. Remember , our modern DVMs don't load the circuit they're measuring like the classic 260 would , and thus the higher readings .

PS , what did the schematic call out for Input voltage ?

If they listed 110 and your at 116 , that could also explain slightly higher readings ...
Reply With Quote
  #3  
Old 02-01-2015, 07:20 PM
stusnyder's Avatar
stusnyder stusnyder is offline
VideoKarma Member
 
Join Date: Nov 2010
Location: northeast Pa
Posts: 486
Quote:
Originally Posted by init4fun View Post
Are you using a modern digital volt meter to take these measurements ?

If so , your readings look fine . If you have a good ol Simpson 260 or other such vintage meter around , I'll bet you find the readings will more closely resemble spec. Remember , our modern DVMs don't load the circuit they're measuring like the classic 260 would , and thus the higher readings .

PS , what did the schematic call out for Input voltage ?

If they listed 110 and your at 116 , that could also explain slightly higher readings ...
I got a simpson, but did not use it. I used a digital. Schematic calls for 117 volts. Maybe I should check with the simpson.
Reply With Quote
  #4  
Old 02-01-2015, 07:23 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Sorry to be a fuddyduddy, but the 260, with sensitivity of 20,000 ohms/volt, will impose a loading of 5 megohms when on the 250V scale (250X20,000=5 meg.).
The only time loading would be a problem with the 260 is in very high impedance circuitry.

In the old days meters typically had sensitivity of 1000 ohms/V, 5000 ohms/V. etc. Those could cause signifigant loading errors.
Reply With Quote
  #5  
Old 02-01-2015, 08:31 PM
stusnyder's Avatar
stusnyder stusnyder is offline
VideoKarma Member
 
Join Date: Nov 2010
Location: northeast Pa
Posts: 486
Ok got the simpson 260 out and checked.

5u4g pin 2 420v should be 382v
5y3 pin 2 220v should be 187
6bf5 pin 6 105v should be 97

The simpson says my line voltage is 125v

Hooked up the variac and dialed in input voltage to 105 volts. At that voltage I get correct readings, but picture is about the same. The top half of the picture just fades away to nothing.

Last edited by stusnyder; 02-01-2015 at 09:44 PM. Reason: more data
Reply With Quote
Audiokarma
  #6  
Old 02-05-2015, 09:39 PM
stusnyder's Avatar
stusnyder stusnyder is offline
VideoKarma Member
 
Join Date: Nov 2010
Location: northeast Pa
Posts: 486
Finally got some progress on this set. I injected a IF signal on the 4th IF tube and I got a decent test pattern. Backed up to the 3rd IF tube and got the half picture. So the problem is before the 4th IF stage. I checked the resistors in the whole IF stage and all the 470 ohms were way out of tolerance, some 200 ohms or more. Replaced them, but still no change.
I also injected a video signal at the video amp and got a decent pic.
The IF section got lots of "dogbone" capacitors. Should I be looking at those, or do I have to search before the IF stage?
Also my voltages are running 30 volts high on the IF stages.
Attached Images
File Type: jpg 20150205_193355.jpg (99.8 KB, 5 views)
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:37 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.