![]() |
|
|
|
#1
|
||||
|
||||
|
And those ceramic caps should really be replaced with modern AC rated X/Y type line bypass caps anyway....
|
|
#2
|
|||
|
|||
|
good catch old coot 88(i didnt see that) and good advice n21xk!
i'm gonna try a 21st century vid phone(skype) service call with mips to get this set sorted out. got a lot going on but will do my best. did a few basic "virual service calls" over the years with non tech friends with great success so im hopeful. it will be easier with a tech (mips) on the other side of the cam! heck-its possible to have several videokarma members advising live using tinychat-is this a new better way to assist vintage tv collectors? new trend? ha! |
|
#3
|
||||
|
||||
|
Yeah I'll fire you a message over Skype and I'll see if I can setup for a call in the next day or so. I wonder if I can get the webcam to behave..
![]() In the meantime I fixed that precariously close wire and did a test fit of everything back in the cabinet. It seems I've neglected to notice I've lost a knob. Uses the keying similar to that used for the mode selector but in this case it's for the contrast. We'll talk about looking for that as well. Tuning needle is also out of alignment by an inch, otherwise there wasn't any other problems.
|
|
#4
|
|||
|
|||
|
Hey Members,
thought i would update on the virtual(skype videophone) service call. 1st of all-Great work Mips! i found giving tech advice is So much easier/better skypeing than typing-lol! the future perhaps? problem #1- two waveforms not correct- scope was set to roughly vert freq-when switched to horz freq-waveforms were correct.Mips found this out before the call. problem#2-too much width-from what i could see, width was close enough-after all, vintage sets are not that accurate-most look fine with designed tolerances at 20%. And i have found over the years that a lot of sets that vintage had very little affect adjusting the width. problem #3-ac leak to chassis.-leaky ac jack-never seen this one but Mips found the problem before the call. problem #4-radio dial out a bit- readjust pointer on dial cord to match station frequency being recieved.ussally an easy fix versus an alignment. problem#4-vertical rolls when adjusting vert height for best picture-height looked good enough to me during the call and vert hold was in the middle of the pot but in hindsite-i should have mentioned that you sometimes have to readjust vert hold while changing vert height/lin-maybe Mips already knew this. problem #5-knob missing-suggested that Mips post a picture of it on here and arfs classified section. problem#6-picture is slightly darker near top of crt-thought it might be a neck shadow but didnt quite look that way to me. Mips mentioned that the tv had uneven sunlight casted on it for a long time so perhaps phosphors could have been affected? in hindsite,i thought that if this is so,you should be able to see a slight difference in the color of the crt phosphor with the set off? it reminded me of a set i fixed years ago where the set was played for a long time with too little height. by the time i got it, the phosphor was brighter where the scan had missed -looked at 1st glance that there was slight vert"foldover". you could see the different color of the phosphor with the set off! problem#7-while vert height was being adjusted, a pf range disc cap blew in the horz section-i thought it was just a coincidence-never heard of a cap blowing in horz while adjusting vert section. most likely a original disc cap ready to blow(across the horz yoke iirc) Problem#7-at one extreme adjusting vert hieght, the scan almost collapses down to aprox 1 inch. but i could see that the vert osc and amp were still working-not a complette collapse-my thoughts are that perhaps with this early desigh, that this is normal. the set can be adjusted for acceptable picture. Mips has replaced most caps(except some ceramics/discs)/checked most resistors. Question#8 Mips showed me some tubluar ceramic caps and wondered if he should change them-iirc, they are ussally good---Mips-could you repost a picture of those caps? any thoughts from the forum? RonL |
![]() |
| Thread Tools | |
| Display Modes | |
|
|