Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Things with Motors

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-28-2014, 09:25 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
more truck work.

Reading the ford forum I found yak about installing a heater control cut off valve.

On that (and many fords IIRC) model ford left the heat core on all the time, and uses a blend door to cut off in max ac mode, but its still in the cab with you and if the blend door leaks you get hot air from the core.

junk yard time find a valve that was used in the later model year (same gen, guess ford decided to use the valve when they went from R-12 to R134a, perhaps it needed a little help keeping cool), grabbed some extra vacuum lines and fittings (needed a T).

before installing valve I wanted to run the vac lines, so had to poke a hole thru a firewall plug, fished a plastic vac line into place, temp hooked up the servo on the valve and then installed the T on the max AC sero (applies vac to operate the recirculate door, so only Max AC will cut out the heater core, this is the way it was plumbed at the factory).

I did a quick test with the eng running to confirm no vac leaks and the servo operated the valve as it should. all good so only need to cut the heater hoses and install. This model uses recirculate valve so both hoses must be cut and 4 connections made.

while at the yard I picked a spare ECU module and power amp, they were cheap so stocked up.
Reply With Quote
  #2  
Old 07-29-2014, 01:59 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
posted up a video of my heater bypass install, no leaks, will have to learn how to paint next. the last time I painted a car was back in the early 1980's and it was with enamel. I presume paint tech has come along way since then.

I would like to just wait for better weather, put up some sheet plastic in the garage for a temp paint booth and have at it.
Reply With Quote
  #3  
Old 07-29-2014, 07:51 PM
TVTim's Avatar
TVTim TVTim is offline
VideoKarma Member
 
Join Date: Nov 2013
Location: Near Harrisburg, PA
Posts: 578
Quote:
Originally Posted by DaveWM View Post
posted up a video of my heater bypass install, no leaks, will have to learn how to paint next. the last time I painted a car was back in the early 1980's and it was with enamel. I presume paint tech has come along way since then.

I would like to just wait for better weather, put up some sheet plastic in the garage for a temp paint booth and have at it.
I painted one car in my life. My 1964 Fairlane. Did all the body work, took off all the trim it was ready. Primed it, came out okay. Put the dark blue on it and the darn thing looked like tiger stripes. Light/dark/light/dark. Had to re-sand the car. Never did paint it again. Good luck with the truck. Would love to see photos.
Reply With Quote
  #4  
Old 07-30-2014, 08:45 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
I will post up some photos later today.

I need some ideas on painting. the paint is good on the sides and the back, the hood I repaint with rattle can paint a while ago. it looked OK but since then the clear has gone to pot AND some dum arse golfer hit me with a bad slice and put a nice ding on the hood that will need to be addressed. Other than that the body is perfect, no dings, no rust, never been bent (I have owned since new).

The top is really shot, the tops of the fenders seem to have lost the clear but the base is still good (I keep in in the garage so no new damage taking place, most of the damage was done years ago when I parked in the sun at work).

I am tempted to see if I can get behind the ding on the hood and at least pop it out a bit, see how it looks, then wet sand it all (I put the base from the rattle cans on pretty heavy) with some 600 grit and see how it looks for re clear. on the top I have considered just painting it gloss white for a two tone (hey its my truck I can do what I want ) that will reflect heat better.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:18 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.