Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-17-2014, 02:58 PM
maxhifi's Avatar
maxhifi maxhifi is offline
VideoKarma Member
 
Join Date: Dec 2010
Posts: 1,871
I think there is some confusion here. "two wire system" is being interpreted two ways, both of which are correct.

1. A "three wire service", is a 120/240V service. If you have a circuit breaker panel this is probably what you have. If you have an electric stove or dryer, this is definitely what you have. The "two wire service" which was 120V only, was a very simple service basically for lighting loads only, and it is very unlikely such a service would still be in existence. I haven't seen one since the 1980s and that was at a house which had been continuously occupied since the late 1930s... finding a two wire 120V service on a house these days is looking for a real antique.

2. "two wire receptacles" means receptacles without a third (grounding) prong. As previously mentioned, if someone at some time replaced the original two prong receptacles with three prong receptacles (as these are more commonly available), the third prong is connected to nothing and thus "floating".

I would imagine your friend is talking about scenario 2, so what to do about it?

1. With any "two prong" electronics this is an absolute non-issue

2. If you must, you can use a GFCI to connect three prong loads, it will detect any current to ground and perform the same job as a ground connection. The Canadian Electrical Code permits a GFCI to be used as a substitute for a ground connection in existing two wire installations - I am not sure if the NEC does or not, but it's a method to improve safety.

3. Add a ground connection to specific existing outlet. Get an appropriate length of #14 XLPE wire, and connect it from the third prong of the specific outlet being grounded back to a solid ground, such as the electrical panel enclosure, or a copper water pipe.

About wire nuts - my house was built in 1962 and all the "wire nuts" are just fine... wire nuts are fine anywhere except where there's vibration, if installed correctly. Push in terminals on receptacles though are just crap, I can't believe they ever got a UL/CSA approval

Last edited by maxhifi; 06-17-2014 at 03:16 PM.
Reply With Quote
  #2  
Old 06-17-2014, 04:31 PM
earlyfilm's Avatar
earlyfilm earlyfilm is offline
Eternal Member
 
Join Date: Jun 2011
Location: Culpeper, VA
Posts: 527
Quote:
Originally Posted by maxhifi View Post
3. Add a ground connection to specific existing outlet. Get an appropriate length of #14 XLPE wire, and connect it from the third prong of the specific outlet being grounded back to a solid ground, such as the electrical panel enclosure, or a copper water pipe.
Some locations require a grounding wire at the utility box and nowhere else. I got in a fight with the inspector in Memphis, because I grounded our washer and dryer to the copper cold water pipe instead of to the central ground. (Our washer and dryer were in an unheated, unfinished, concrete-floor utility room outside of the back of our house.) I did this because if something fails and the ground wire becomes hot and I wanted no possibility for a shock in this potentially wet area.

I then suggested to the inspector that I tie both together, and was told specifically that it was not permitted.

James
Reply With Quote
  #3  
Old 06-17-2014, 05:30 PM
maxhifi's Avatar
maxhifi maxhifi is offline
VideoKarma Member
 
Join Date: Dec 2010
Posts: 1,871
Quote:
Originally Posted by earlyfilm View Post
Some locations require a grounding wire at the utility box and nowhere else. I got in a fight with the inspector in Memphis, because I grounded our washer and dryer to the copper cold water pipe instead of to the central ground. (Our washer and dryer were in an unheated, unfinished, concrete-floor utility room outside of the back of our house.) I did this because if something fails and the ground wire becomes hot and I wanted no possibility for a shock in this potentially wet area.

I then suggested to the inspector that I tie both together, and was told specifically that it was not permitted.

James
Yes, if you ground at more than one point you might create a ground loop, and get circulating currents. I said to ground to a pipe because realistically, it may be totally impractical to run a wire all the way back to the panel and there could be a water or radiator pipe staring you in the face. Of course I am assuming your water pipes are all metal and are grounded too, but given the age of the house it's probably a reasonable assumption.

Electrical code is designed in such a way as to be fool proof, but it is far from the only way to make something safe and reliable. Of course I am making the assumption that the pipe is a good ground, but it's not hard to verify if it is. Look at how wiring is done in Europe... much of it would NEVER pass inspection in north America but you don't hear scary statistics about electrical fires and electrocutions in Europe.
Reply With Quote
  #4  
Old 06-17-2014, 08:08 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Some really scary stuff like house fires was recounted in the aluminum wiring fiasco.
Reply With Quote
  #5  
Old 06-17-2014, 04:53 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by maxhifi View Post
...The "two wire service" which was 120V only, was a very simple service basically for lighting loads only, and it is very unlikely such a service would still be in existence. I haven't seen one since the 1980s and that was at a house which had been continuously occupied since the late 1930s... finding a two wire 120V service on a house these days is looking for a real antique. ...

Push in terminals on receptacles though are just crap, I can't believe they ever got a UL/CSA approval
My grandma's house, in 1984, had that 2 wire service. POCO cones into the basement, thru a 30A screw in fuse, then the meter, then to a pair of 15A fuses, and the neutral also had fuses, we used 30A fuses there, so the hot side 15A fuses would be the ones to blow. If we wanted to, we could have easily grabbed unmetered power at that first 30A fuse. But we didn't.

As for the push in terminals, I've heard electricians call them "Push and pray".
__________________
Reply With Quote
Audiokarma
  #6  
Old 06-17-2014, 05:24 PM
maxhifi's Avatar
maxhifi maxhifi is offline
VideoKarma Member
 
Join Date: Dec 2010
Posts: 1,871
Quote:
Originally Posted by wa2ise View Post
My grandma's house, in 1984, had that 2 wire service. POCO cones into the basement, thru a 30A screw in fuse, then the meter, then to a pair of 15A fuses, and the neutral also had fuses, we used 30A fuses there, so the hot side 15A fuses would be the ones to blow. If we wanted to, we could have easily grabbed unmetered power at that first 30A fuse. But we didn't.

As for the push in terminals, I've heard electricians call them "Push and pray".
I am assuming 1894 - that's cool, my great grandparents house had that sort of a set up too, that's why they had a gas range and gas dryer.
Reply With Quote
  #7  
Old 06-18-2014, 09:34 AM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by maxhifi View Post
I am assuming 1894 - that's cool, my great grandparents house had that sort of a set up too, ...
My grandma's house probably was built around 1894, but it still had the same wiring when my grandma checked out, in 1984. World's earliest BX cable, you look at it crosseyed, and the insulation turns to powder... The subsequent owner has upgraded the wiring, and installed air conditioning.

The house was a classic grandma's house, with a front porch, a back porch, full attic, and an added big kitchen in the back.
__________________
Reply With Quote
  #8  
Old 06-18-2014, 10:25 AM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by wa2ise View Post
My grandma's house probably was built around 1894, but it still had the same wiring when my grandma checked out, in 1984. World's earliest BX cable, you look at it crosseyed, and the insulation turns to powder... The subsequent owner has upgraded the wiring, and installed air conditioning.

The house was a classic grandma's house, with a front porch, a back porch, full attic, and an added big kitchen in the back.
I lived in a few houses like that, being the oldest section of town.
Many of them had additions, as well.
If the home has that early BX, it was wired for electricity, well after it was built. The real hi-class homes had gas piping in the walls. Slightly newer homes had K&T wiring, as well as gas lines.
The old family home was wired in the mid-1920's. Back then, the electric utility, subsidized the wiring installation.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:21 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.