Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-30-2013, 03:00 PM
Zenith26kc20's Avatar
Zenith26kc20 Zenith26kc20 is offline
VideoKarma Member
 
Join Date: Apr 2009
Location: New Orleans
Posts: 860
Been a while but if I remember right, that is a C2 chassis. Look around the power supply area (middle of the board on the right for weak or open capacitors. Also, look around the video jungle IC on the other board. The picture you have shown looks like a bad capacitor on the Jungle IC. It is not the large IC heading to the back. That would be the MTS IC. You virtually have to have a ESR type capacitor tester for this set. Look around the small (1 uf up to 4.7 uf) caps for liquid leaking out on the PC board. These sets were very good performers when working. The PIP modules almost always have a dozen or so dead capacitors in them. Also, look around the front of the power supply board for larger leaking capacitors. Look under the vertical IC for bad solder connections. Also, vertical fold over is going to be bad capacitors around the vertical IC. There were a lot of these sets here until Katrina got them
Reply With Quote
  #2  
Old 12-30-2013, 03:35 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by Zenith26kc20 View Post
Been a while but if I remember right, that is a C2 chassis. Look around the power supply area (middle of the board on the right for weak or open capacitors. Also, look around the video jungle IC on the other board. The picture you have shown looks like a bad capacitor on the Jungle IC. It is not the large IC heading to the back. That would be the MTS IC. You virtually have to have a ESR type capacitor tester for this set. Look around the small (1 uf up to 4.7 uf) caps for liquid leaking out on the PC board. These sets were very good performers when working. The PIP modules almost always have a dozen or so dead capacitors in them. Also, look around the front of the power supply board for larger leaking capacitors. Look under the vertical IC for bad solder connections. Also, vertical fold over is going to be bad capacitors around the vertical IC. There were a lot of these sets here until Katrina got them
Thanks for all the suggestions. I'm afraid I'm not familiar with the term PIP modules?
Reply With Quote
  #3  
Old 12-30-2013, 03:59 PM
Zenith26kc20's Avatar
Zenith26kc20 Zenith26kc20 is offline
VideoKarma Member
 
Join Date: Apr 2009
Location: New Orleans
Posts: 860
Picture in Picture. It was a large rectangular box on the signal (left viewed from the back). Not all sets had them. I don't remember what terminals were jumpered if the module failed (disabling the PIP). If you get it running I'll look it up in my notes. The broken up picture was almost always a small capacitor by the video jungle IC. Intermittant startup/no start was a cap around the heatsink in the middle of the power supply. I liked these chassis. They can produce a great picture.
Reply With Quote
  #4  
Old 12-30-2013, 04:21 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Thanks for the explanation. Is there a way to safely power the two main boards on the bench without removal of the front switch panel PC board? Any voltage test points to verify correct power supply operation?
Reply With Quote
  #5  
Old 12-30-2013, 05:29 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Well I had to take the two PC boards out of the plastic tray to get at the solder side. Boy that white goo holding the connecters was a treat to remove. I see at least a couple caps that have leaked electrolyte onto the video board.





Reply With Quote
Audiokarma
  #6  
Old 12-30-2013, 11:17 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
These are the caps I've found so far on the main board that show physical signs of leakage. It looks like the Nichicon PC(M) series are the culprits, the darker blue and black ones seem OK. In several places the electrolyte has seeped through to the copper traces and made a corrosion mess. Lots of PC trace rework is in order. I'm going to have to place a cap order.





Reply With Quote
  #7  
Old 12-31-2013, 08:03 AM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
The transistor is either the power supply FET or the HOT.
The HOT on most mid 80's up sets have a damper diode
E-C & a resistor B-E. 99.9% dead short when they fail.
Power FET's can dead short D-S or open. The one
board Zeniths had 2 small 'lytics in the PS that caused
int dead or dead. The 2 boarders were big sets so almost
all were done in home at board level til near the end.
For the control board it helps to have one of those 3 foot
long xelite 1/4 drivers. I still got mine but you will have to
pull it out of my cold dead hands.
I will look later today for the manual.

73 Zeno
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:52 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.