Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-30-2013, 01:11 PM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by Kevin Kuehn View Post
Well duh, the board numbers were on a paper label on the inside of the cabinet.

9-959 Main
9-1075 SMPS/Sweep

Since I've gotten this thing to my place it's back to not powering on. When I push the power switch the green light on the front comes on, but the power relay does not pull in. Pushing the switch a second time won't turn the light back off. So I suspect there's something flaky with the on-off circuitry.

[edit] Actually the green light that comes on is the stereo indicator. But it won't turn off when the power switch is pushed a second time.
I looked through my junk stash and I have a chassis assembly, that came from a set very similar to the one you're working with. The main board is a 9-959, but the sweep is a 9-754-1.
The original problem was the set wouldn't always start the first time.
I pulled the boards and found a few solder connections that were loose.
I returned and it still wouldn't work and the owner said forget it.
If you think you could use them, P.M. me.
Reply With Quote
  #2  
Old 12-30-2013, 01:46 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by dieseljeep View Post
I looked through my junk stash and I have a chassis assembly, that came from a set very similar to the one you're working with. The main board is a 9-959, but the sweep is a 9-754-1.
The original problem was the set wouldn't always start the first time.
I pulled the boards and found a few solder connections that were loose.
I returned and it still wouldn't work and the owner said forget it.
If you think you could use them, P.M. me.
Thanks for the offer, I'll think about that. At this point I'm not too sure I want to keep beating my head over this thing. Without a proper road map these solid state sets are just a major frustration to me. Life's too short and there's a lot of tube sets that are more worthy of my time.
Reply With Quote
  #3  
Old 12-30-2013, 03:00 PM
Zenith26kc20's Avatar
Zenith26kc20 Zenith26kc20 is offline
VideoKarma Member
 
Join Date: Apr 2009
Location: New Orleans
Posts: 860
Been a while but if I remember right, that is a C2 chassis. Look around the power supply area (middle of the board on the right for weak or open capacitors. Also, look around the video jungle IC on the other board. The picture you have shown looks like a bad capacitor on the Jungle IC. It is not the large IC heading to the back. That would be the MTS IC. You virtually have to have a ESR type capacitor tester for this set. Look around the small (1 uf up to 4.7 uf) caps for liquid leaking out on the PC board. These sets were very good performers when working. The PIP modules almost always have a dozen or so dead capacitors in them. Also, look around the front of the power supply board for larger leaking capacitors. Look under the vertical IC for bad solder connections. Also, vertical fold over is going to be bad capacitors around the vertical IC. There were a lot of these sets here until Katrina got them
Reply With Quote
  #4  
Old 12-30-2013, 03:35 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by Zenith26kc20 View Post
Been a while but if I remember right, that is a C2 chassis. Look around the power supply area (middle of the board on the right for weak or open capacitors. Also, look around the video jungle IC on the other board. The picture you have shown looks like a bad capacitor on the Jungle IC. It is not the large IC heading to the back. That would be the MTS IC. You virtually have to have a ESR type capacitor tester for this set. Look around the small (1 uf up to 4.7 uf) caps for liquid leaking out on the PC board. These sets were very good performers when working. The PIP modules almost always have a dozen or so dead capacitors in them. Also, look around the front of the power supply board for larger leaking capacitors. Look under the vertical IC for bad solder connections. Also, vertical fold over is going to be bad capacitors around the vertical IC. There were a lot of these sets here until Katrina got them
Thanks for all the suggestions. I'm afraid I'm not familiar with the term PIP modules?
Reply With Quote
  #5  
Old 12-30-2013, 03:59 PM
Zenith26kc20's Avatar
Zenith26kc20 Zenith26kc20 is offline
VideoKarma Member
 
Join Date: Apr 2009
Location: New Orleans
Posts: 860
Picture in Picture. It was a large rectangular box on the signal (left viewed from the back). Not all sets had them. I don't remember what terminals were jumpered if the module failed (disabling the PIP). If you get it running I'll look it up in my notes. The broken up picture was almost always a small capacitor by the video jungle IC. Intermittant startup/no start was a cap around the heatsink in the middle of the power supply. I liked these chassis. They can produce a great picture.
Reply With Quote
Audiokarma
  #6  
Old 12-30-2013, 04:21 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Thanks for the explanation. Is there a way to safely power the two main boards on the bench without removal of the front switch panel PC board? Any voltage test points to verify correct power supply operation?
Reply With Quote
  #7  
Old 12-30-2013, 05:29 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Well I had to take the two PC boards out of the plastic tray to get at the solder side. Boy that white goo holding the connecters was a treat to remove. I see at least a couple caps that have leaked electrolyte onto the video board.





Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:14 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.