Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-28-2013, 01:14 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
Quote:
Originally Posted by Kevin Kuehn View Post
Would checking the HV verify if this is the case? I searched the Sams website but nothing comes up using the sets model number. Did Sams not provide service info for these era Zeniths? I'm more less curious because I doubt this thing is worth investing in the paperwork. My fear is that when I fix one problem, another issue will soon surface.
This is an SS model. Most were sold in the big stores or were
drop ins. Sometimes we could get them. If not we didnt even
get the spec sheets. Same case with S, T, ST, V & SV models.
Get the 9-*** numbers off the 2 main boards & I can see what I
have on it. It will be near identical to a regular line set.
As far as reliability goes these were decent. Some FBT's went
but completely, no raster followed by shut-down & the HOT
overheats.
Reply With Quote
  #2  
Old 12-29-2013, 08:47 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by zeno View Post
Get the 9-*** numbers off the 2 main boards & I can see what I
have on it. It will be near identical to a regular line set.
Finally have the set at my place. Offhand I don't see those 9-*** numbers on the two boards. Are they possibly on the bottom side, or hidden by the board mounting tray?
Reply With Quote
  #3  
Old 12-29-2013, 10:07 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Well duh, the board numbers were on a paper label on the inside of the cabinet.

9-959 Main
9-1075 SMPS/Sweep

Since I've gotten this thing to my place it's back to not powering on. When I push the power switch the green light on the front comes on, but the power relay does not pull in. Pushing the switch a second time won't turn the light back off. So I suspect there's something flaky with the on-off circuitry.

[edit] Actually the green light that comes on is the stereo indicator. But it won't turn off when the power switch is pushed a second time.

Last edited by Kevin Kuehn; 12-29-2013 at 10:20 PM.
Reply With Quote
  #4  
Old 12-30-2013, 01:08 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Pulled the PC boards out and was poking around looking for suspect capacitors. Just for the heck of it I checked the big transistor mounted on the heatsink next to the flyback transformer. Out of circuit it measures 53 ohms in both directions across the base-emitter. That can't be right, can it?




Last edited by Kevin Kuehn; 12-30-2013 at 01:37 PM.
Reply With Quote
  #5  
Old 12-30-2013, 01:14 PM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by Kevin Kuehn View Post
Pulled the PC boards out and was poking around looking for suspect capacitors. Just for the heck of it I checked the big transistor mounted on the heatsink next to the flyback transformer. Out of circuit it measures 53 ohms in both directions across the base-emitter. That can't be right, can it?



Those things fool you because of the built damper diode. If it was truly shorted, it would read 0 ohms in both directions.
Reply With Quote
Audiokarma
  #6  
Old 12-30-2013, 01:31 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by dieseljeep View Post
Those things fool you because of the built damper diode. If it was truly shorted, it would read 0 ohms in both directions.
Well I was wondering about that too, but this thing shows .034 drop in both directions when my Fluke 75 is in diode check, but it also shows 53 ohms resistance in both directions.
Reply With Quote
  #7  
Old 12-31-2013, 06:32 PM
N2IXK's Avatar
N2IXK N2IXK is offline
Technohippie
 
Join Date: Apr 2011
Location: Sittin' on the "Group W" bench...
Posts: 817
Quote:
Originally Posted by Kevin Kuehn View Post
Well I was wondering about that too, but this thing shows .034 drop in both directions when my Fluke 75 is in diode check, but it also shows 53 ohms resistance in both directions.
Many of the HOTs that contained built-in damper diodes also had a 50-100 ohm internal resistor across the B-E junction. I'm sure this is what you are seeing here.

If it was not blowing fuses and generating HV, the HOT is likely just fine.
Reply With Quote
  #8  
Old 12-30-2013, 01:11 PM
dieseljeep dieseljeep is offline
VideoKarma Member
 
Join Date: Jul 2010
Posts: 7,562
Quote:
Originally Posted by Kevin Kuehn View Post
Well duh, the board numbers were on a paper label on the inside of the cabinet.

9-959 Main
9-1075 SMPS/Sweep

Since I've gotten this thing to my place it's back to not powering on. When I push the power switch the green light on the front comes on, but the power relay does not pull in. Pushing the switch a second time won't turn the light back off. So I suspect there's something flaky with the on-off circuitry.

[edit] Actually the green light that comes on is the stereo indicator. But it won't turn off when the power switch is pushed a second time.
I looked through my junk stash and I have a chassis assembly, that came from a set very similar to the one you're working with. The main board is a 9-959, but the sweep is a 9-754-1.
The original problem was the set wouldn't always start the first time.
I pulled the boards and found a few solder connections that were loose.
I returned and it still wouldn't work and the owner said forget it.
If you think you could use them, P.M. me.
Reply With Quote
  #9  
Old 12-30-2013, 01:46 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by dieseljeep View Post
I looked through my junk stash and I have a chassis assembly, that came from a set very similar to the one you're working with. The main board is a 9-959, but the sweep is a 9-754-1.
The original problem was the set wouldn't always start the first time.
I pulled the boards and found a few solder connections that were loose.
I returned and it still wouldn't work and the owner said forget it.
If you think you could use them, P.M. me.
Thanks for the offer, I'll think about that. At this point I'm not too sure I want to keep beating my head over this thing. Without a proper road map these solid state sets are just a major frustration to me. Life's too short and there's a lot of tube sets that are more worthy of my time.
Reply With Quote
  #10  
Old 12-30-2013, 03:00 PM
Zenith26kc20's Avatar
Zenith26kc20 Zenith26kc20 is offline
VideoKarma Member
 
Join Date: Apr 2009
Location: New Orleans
Posts: 860
Been a while but if I remember right, that is a C2 chassis. Look around the power supply area (middle of the board on the right for weak or open capacitors. Also, look around the video jungle IC on the other board. The picture you have shown looks like a bad capacitor on the Jungle IC. It is not the large IC heading to the back. That would be the MTS IC. You virtually have to have a ESR type capacitor tester for this set. Look around the small (1 uf up to 4.7 uf) caps for liquid leaking out on the PC board. These sets were very good performers when working. The PIP modules almost always have a dozen or so dead capacitors in them. Also, look around the front of the power supply board for larger leaking capacitors. Look under the vertical IC for bad solder connections. Also, vertical fold over is going to be bad capacitors around the vertical IC. There were a lot of these sets here until Katrina got them
Reply With Quote
Audiokarma
  #11  
Old 12-30-2013, 03:35 PM
Kevin Kuehn's Avatar
Kevin Kuehn Kevin Kuehn is offline
Workin' Late Again
 
Join Date: Jan 2011
Location: WI
Posts: 3,976
Quote:
Originally Posted by Zenith26kc20 View Post
Been a while but if I remember right, that is a C2 chassis. Look around the power supply area (middle of the board on the right for weak or open capacitors. Also, look around the video jungle IC on the other board. The picture you have shown looks like a bad capacitor on the Jungle IC. It is not the large IC heading to the back. That would be the MTS IC. You virtually have to have a ESR type capacitor tester for this set. Look around the small (1 uf up to 4.7 uf) caps for liquid leaking out on the PC board. These sets were very good performers when working. The PIP modules almost always have a dozen or so dead capacitors in them. Also, look around the front of the power supply board for larger leaking capacitors. Look under the vertical IC for bad solder connections. Also, vertical fold over is going to be bad capacitors around the vertical IC. There were a lot of these sets here until Katrina got them
Thanks for all the suggestions. I'm afraid I'm not familiar with the term PIP modules?
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:21 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.