Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-04-2013, 05:01 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
Quote:
Originally Posted by andy View Post
I think you meant to say that the cathodes are where the video signal is applied to the CRT. G1, and G2 should have DC on them.
oops right thanks Andy.

Tin Can just do the check on the cathodes with the scope for now with the transmitted blank screen, use the horz rate, AC, make sure you can see the entire trace including two horz sync pulses.

after that the G1 and the G2, If you scope works like mine the AC setting should allow you to look at the G2 (using 10x and 5v would be 50v per div) since it should see very little AC at all, assuming the filter caps are ok on those supplies (the 250 and the 870, both derived in the horz circuit). If you want you could start by turning the screen pots fully CCW that would place the G2 at the lowest DC voltage of 250v (but again it should not matter as there should be NO ac anyway).

Last edited by DaveWM; 10-04-2013 at 05:15 PM.
Reply With Quote
  #2  
Old 10-04-2013, 06:04 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by DaveWM View Post
oops right thanks Andy.

Tin Can just do the check on the cathodes with the scope for now with the transmitted blank screen, use the horz rate, AC, make sure you can see the entire trace including two horz sync pulses.

after that the G1 and the G2, If you scope works like mine the AC setting should allow you to look at the G2 (using 10x and 5v would be 50v per div) since it should see very little AC at all, assuming the filter caps are ok on those supplies (the 250 and the 870, both derived in the horz circuit). If you want you could start by turning the screen pots fully CCW that would place the G2 at the lowest DC voltage of 250v (but again it should not matter as there should be NO ac anyway).
Okay, I know the G2s are in the bottom right of this schematic and feed the higher voltage (540 - 640V) pins on the CRT. Are the G1s the ones in the 140V range and the cathodes in the 36V range? If so, should I test at the pins of the CRT or find a spot on the chassis?

You'll also note the test points on the schematic that feed the taps, etc. Are those ones I should scope? And if so, do they take the place of doing so on the CRT pins for those?
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #3  
Old 10-04-2013, 06:28 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Here are a few pics. First one is contrast down and brightness up. Second is brightness and contrast up. Third is a question as to whether I need to redo purity of if it needs a good degauss.
Attached Images
File Type: jpg Full Bright JBs.jpg (84.3 KB, 12 views)
File Type: jpg Full Bright Cont JBs.jpg (73.8 KB, 12 views)
File Type: jpg Purity or degauss.jpg (42.8 KB, 13 views)
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #4  
Old 10-04-2013, 07:35 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
wow looks pretty good in the second pic, how does that look with regular content? can you adj for good contrast and reasonable brightness and not have jail bars? Now I wonder if there is a problem or are you just asking too much of it. Remember jail bar exist due to lack of complete blanking in retrace, if the CRT bias setups (contrast/brighness/G2) are pushed to an extreme I would not be surprised that they could show thru.

as far as were to hook up, I would pull the CRT socket back a tad and use the clip on style scope probe.
Reply With Quote
  #5  
Old 10-04-2013, 07:36 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
you have a very slight purity issue, I would leave it alone as rarely will you notice that with regular viewing.
Reply With Quote
Audiokarma
  #6  
Old 10-04-2013, 07:49 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by DaveWM View Post
wow looks pretty good in the second pic, how does that look with regular content? can you adj for good contrast and reasonable brightness and not have jail bars? Now I wonder if there is a problem or are you just asking too much of it. Remember jail bar exist due to lack of complete blanking in retrace, if the CRT bias setups (contrast/brighness/G2) are pushed to an extreme I would not be surprised that they could show thru.

as far as were to hook up, I would pull the CRT socket back a tad and use the clip on style scope probe.
Thing is, the second picture is full contrast AND full brightness w/massive blooming. It's definitely being overdriven. If you try to watch program content, it is way too bright and washed out. The jail bars are the most noticeable with normal levels of brightness and contrast.

I usually bring up the contrast to the point of blooming and then back it off. I then keep backing it off until the level is right for the viewing environment. I then adjust brightness up until I get decent shading in the dark areas of the picture. Sometimes I have to go back and forth between the two controls to get it right. In no way am I driving it too hard with those controls and the G2 voltages are within range.

Tomorrow will be my day for checking the cathodes, G1 and G2s.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:55 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.