Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-09-2013, 01:11 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by Username1 View Post
If you replaced the Horiz osc board with a known good one, move on, If you have a known good voltage divider and want to replace it, do so, then move on. With parts of the Horiz. circuit out of the way, move on over to the flyback, and parts that may be mounted near it.

You will have to check items on the chassis that are part of the horiz. that are not on the module.

When you say diodes had their leads cut then resoldered, did they cut one side, then resolder, or cut both sides...? Both sides may mean they chose to replace the part from on top of the board, I have seen that before, cutting one side may just be to test it with a vom.
They cut only one lead and resoldered. I'm assuming they were testing, found nothing and soldered the leg back. No replacements were done.

Okay, just purchased a Tektronix 465M Oscilloscope, NIST-certified, Guaranteed & NIST calibrated off ebay. Hopefully it will be here around this time next week.

So I guess I'll just change the divider and let her be until the scope arrives. Now you said I need two probes? If so, I'll order another of the one I already have.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #2  
Old 09-09-2013, 05:23 PM
Username1's Avatar
Username1 Username1 is offline
Not sure how I got here.
 
Join Date: Dec 2009
Location: Orange County NY
Posts: 3,668
Quote:
Originally Posted by TinCanAlley View Post
They cut only one lead and resoldered. I'm assuming they were testing, found nothing and soldered the leg back. No replacements were done.

Okay, just purchased a Tektronix 465M Oscilloscope, NIST-certified, Guaranteed & NIST calibrated off ebay. Hopefully it will be here around this time next week.

So I guess I'll just change the divider and let her be until the scope arrives. Now you said I need two probes? If so, I'll order another of the one I already have.
A 465M is a really good scope, one of my favorites, Calibration certified means you can get your money back if you decide to sell one day. I bet it was expensive, be sure you get the papers. Be sure to get probes so you can use it when you get it.

2 probes are an option, your scope will get a trigger signal off whatever you apply to one channel, the second probe is just in case you need to use a separate trigger source, good idea to have for some needs. Be sure you get ones with 1x 10x options and trimmer adjustment for capacitance, this will match impedance properly. Your scope has a square wave test point on its front, attach the probe, and adjust the trimmer to get a nice square wave with no overshoot, or loading (rounding of the square edges).

Just for the heck of it, when you just set that tv up to run as normal, and wack it a few times does anything happen to either the sound or picture that would indicate any loose connections, since this is a module set, any indication of disturbance while hitting it may mean you have bad plugs, or connectors on the boards....?
__________________
Yes you can call me "Squirrel boy"

Last edited by Username1; 09-09-2013 at 05:33 PM.
Reply With Quote
  #3  
Old 09-09-2013, 07:11 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by Username1 View Post
A 465M is a really good scope, one of my favorites, Calibration certified means you can get your money back if you decide to sell one day. I bet it was expensive, be sure you get the papers. Be sure to get probes so you can use it when you get it.

2 probes are an option, your scope will get a trigger signal off whatever you apply to one channel, the second probe is just in case you need to use a separate trigger source, good idea to have for some needs. Be sure you get ones with 1x 10x options and trimmer adjustment for capacitance, this will match impedance properly. Your scope has a square wave test point on its front, attach the probe, and adjust the trimmer to get a nice square wave with no overshoot, or loading (rounding of the square edges).

Just for the heck of it, when you just set that tv up to run as normal, and wack it a few times does anything happen to either the sound or picture that would indicate any loose connections, since this is a module set, any indication of disturbance while hitting it may mean you have bad plugs, or connectors on the boards....?
I have one 10x probe already (just purchased it a couple of weeks ago) and have order a second one. They do have the trimmer adjustment, so I think all will be good when the scope arrives.

The scope is supposed to come with a calibration certificate. I'll probably keep it afterwards and start scoping anything and everything. I know if I get rid of it, I'll need it.

I guess I can use something to tap around on the chassis and modules to see if there's something loose (think I have a drum stick around somewhere). Whacking the set does no good as it's a solid cabinet and only serves to sting my hand.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #4  
Old 09-09-2013, 08:37 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by Username1 View Post
2 probes are an option, your scope will get a trigger signal off whatever you apply to one channel, the second probe is just in case you need to use a separate trigger source, good idea to have for some needs. Be sure you get ones with 1x 10x options and trimmer adjustment for capacitance, this will match impedance properly. Your scope has a square wave test point on its front, attach the probe, and adjust the trimmer to get a nice square wave with no overshoot, or loading (rounding of the square edges).
I do have a question about test points. In the Sams it shows a test point between one leg of the vertical transistor and one leg of the horizontal blanking transistor. Seems the two legs are tied together and then a resistor goes to ground from that solder point. Now the test point is right at that junction and it can only be reached from the bottom of the chassis. Is it important to get that point or can I just connect the probe on the top side directly to the leg of the blanker transistor? Either way it's on the same end of the resistor, so that's not an issue. It's just not at the solder point of the two legs.

I hope that makes sense.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:28 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.