Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Solid State CRT Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 08-15-2013, 02:31 PM
WISCOJIM WISCOJIM is offline
VideoKarma Member
 
Join Date: Sep 2005
Location: Grand Chute, Wisconsin
Posts: 2,508
Quote:
Originally Posted by TinCanAlley View Post
It's Photofacts 1370-2n. If you look at page 16 you'll see parts identified via arrows on a picture of the underside of the chassis. On that page you'll find R202, R203 and R207 (all of which I've verified as being on my chassis). When you go to page 22 where the resistors are listed, it jumps from R201 to R206 and jumps again to R227. Quite a few have been skipped.
Apparently Photofacts made a change at some point to list only the "Power & Special" resistors according to the heading on page 22. I was not aware of that because I rarely ever work with Photofacts on equipment that new. The schematic page does state that all resistors shown (unless otherwise marked) as being 1/2 watt or less. No need to use 1 watters.
Reply With Quote
  #2  
Old 08-15-2013, 02:51 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by WISCOJIM View Post
Apparently Photofacts made a change at some point to list only the "Power & Special" resistors according to the heading on page 22. I was not aware of that because I rarely ever work with Photofacts on equipment that new. The schematic page does state that all resistors shown (unless otherwise marked) as being 1/2 watt or less. No need to use 1 watters.
So, basically, if it's only noted by value I should replace it with a 5% 1/2 watt? I don't think I'd be able to tell the wattage, so the 1/2 watt 5% would cover just about all of them.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650

Last edited by TinCanAlley; 08-15-2013 at 03:02 PM.
Reply With Quote
  #3  
Old 08-15-2013, 03:31 PM
WISCOJIM WISCOJIM is offline
VideoKarma Member
 
Join Date: Sep 2005
Location: Grand Chute, Wisconsin
Posts: 2,508
Quote:
Originally Posted by TinCanAlley View Post
So, basically, if it's only noted by value I should replace it with a 5% 1/2 watt? I don't think I'd be able to tell the wattage, so the 1/2 watt 5% would cover just about all of them.
Yes, 1/2 watt unless otherwise noted. The originals were 10% & 20% tolerance, but 5% tolerance resistors are now available without the large cost premium they had in years past.
Reply With Quote
  #4  
Old 08-15-2013, 04:22 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by WISCOJIM View Post
Yes, 1/2 watt unless otherwise noted. The originals were 10% & 20% tolerance, but 5% tolerance resistors are now available without the large cost premium they had in years past.
Sure wish there was a local place that had the selection of Mouser. Still, I usually get my stuff in 4 days.

Thanks!
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
  #5  
Old 08-15-2013, 06:13 PM
zeno's Avatar
zeno zeno is offline
VideoKarma Member
 
Join Date: Mar 2013
Location: New Hampshire
Posts: 4,918
Metal film is fine. On a SS set there is some risk going
with higher watt resistors. In some cases like the 330 ohm
on your 9-57 ( also on 9-90 ) board need to go from 1/2
up to 1w due to a near 100% failure rate. One place you
should never go up is low value resistors. They are often
used as a fuse only. Newer sets use a lot of them.

73 Zeno
Reply With Quote
Audiokarma
  #6  
Old 08-15-2013, 08:57 PM
TinCanAlley's Avatar
TinCanAlley TinCanAlley is offline
VideoKarma Member
 
Join Date: Sep 2008
Location: So Cal, CA
Posts: 1,026
Quote:
Originally Posted by zeno View Post
Metal film is fine. On a SS set there is some risk going
with higher watt resistors. In some cases like the 330 ohm
on your 9-57 ( also on 9-90 ) board need to go from 1/2
up to 1w due to a near 100% failure rate. One place you
should never go up is low value resistors. They are often
used as a fuse only. Newer sets use a lot of them.

73 Zeno
I wish there were a way to know if it's a 1/4 or 1/2 just by looking. If a low value might be used as a fuse, they should note the wattage. As it is, the schematics only state that they are 1/2 or less unless noted. Well that doesn't do much to help if the resistor is meant to be no higher than a 1/4.

So is there some kind of guideline with regards to resistor value and wattage? Is there a certain value where anything at or below it is usually a 1/4 and anything above it goes to 1/2 and more as the value increases? Or is value independent of the heat it dissipates?

Must admit I'm learning lots lately. Once I get the Avanti up and fully functional, I'm taking what I've learned and giving the 19JC55Z chassis at thorough going over as well.
__________________
Pioneer SX-1080, Pioneer PL-115D, Pioneer CT-F9191, Pioneer RG-1, Wollensak 8050A, Akai 4000DS MkII, Pioneer CS-05 & Polk 1.2TL

Denon 5803A, Pioneer DVL-700, Pioneer CT-W603RS, Toshiba HD-A3, D-Link DSM-520, Dish VIP-722, Polk 1.2TL, CSi5, LS/fx, RT-800 and PSW-650
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:21 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.