Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Vintage TV & Radio Tech Forum

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 08-11-2013, 01:28 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Sorta works !

For grins, yesterday afternoon I dug most of the parts out of my junk box to build a simple version of the Li'l 7. I do not have the proper oscillator coil, but found small antenna coil (likely out of a junked AM radio) that had 2 separate windings. The windings both had fairly low resistance (under 10 ohms), but I decided to give it a try. I did not use a power transformer for isolation, but made sure that ground on the board was always cold. I could not find a 1 meg pot, so I substituted a 1.2 meg resistor to ground at the input (pin 5).

Since the coil was not identified in any way, I connected the lower resistance winding (untuned) to the plate (pin 3) and B+ and used the higher resistance winding (tuned with a 270pf cap) in the feedback circuit (pin 4 and ground). A 6.3 VAC 60Hz "signal" from a bench power supply was connected to the input (pin 5) and ground.

I had to reverse the two leads in the feedback circuit to get oscillation, but when I did, I was able to find a loud buzz with a portable radio very near the transmitter. Since my "oscillator coil" does not have an adjustable slug for tuning, I merely scanned the band with the portable radio... found the buzz "signal" at about 700kHz. The range was only about 5 feet with no antenna connected to the transmitter.

Now the "sorta" part... when the signal was removed, it appeared that the transmitter stopped transmitting! In fact, there seemed to be a threshold... if the signal was reduced below a certain point oscillation stopped. I suspect that a real audio signal would be transmitted, but with much distortion, as bob91343 suggested.

Perhaps with the correct oscillator coil, the circuit *might* work ok, I don't know... today if I get a chance, I will try to "bias up" the G2 connection to a positive source to see if I can get undistorted modulation. As can be seen in the 'scope photo, alternate parts of the 60Hz test signal (likely the negative portions) are missing from the modulated output of the transmitter.

jr

Last edited by jr_tech; 05-30-2017 at 04:35 PM.
Reply With Quote
  #2  
Old 08-11-2013, 02:32 PM
Geist Geist is offline
VideoKarma Member
 
Join Date: Dec 2012
Posts: 350
Hi All;
Jr tech, If you put a tuning cap in parallel with your coil, you could tune it to where ever you want..
That is in the schematic I posted, He had a tuning cap in the circuit.. He states in the article that an antenna coil or an oscillator coil will work, with a tuning cap..
THANK YOU Marty
Reply With Quote
  #3  
Old 08-11-2013, 02:49 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
For sure... but I used all the 365pf tuning caps that I had when I built a number of tuned loop antennas for myself and several friends... still digging in "junk boxes", might find something suitable.
"Fixed tuned" worked well enough for my purpose of testing the operation of the circuit.

jr

Update: I "biased up" the G2 somewhat by connecting it through a 470k resistor to the B+ supply. G2 now sets at about + 25 volts. The modulated output is no longer missing the negative information from the modulating signal and the transmitter continues to oscillate when the modulating signal is removed, but it is not very symmetrical (sorry 'bout the fuzzy handheld pix). The tube is now drawing more current and the B+ supply has dropped to about 110 VDC. Obviously, the 10k resistor in the power supply will have to be reduced, and likely more filtering will be needed to handle the increased current load. More work is needed, but out of time for today.

Last edited by jr_tech; 05-06-2017 at 02:20 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:17 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.