Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 07-16-2013, 01:22 AM
kramden66 kramden66 is offline
VideoKarma Member
 
Join Date: Nov 2010
Location: Rockaway, NJ
Posts: 1,421
In this set the electrolytics are 475 volts , i have a feeling that a 450 volt would be ok its just the start up voltage may go at or above 450 volts and then drop thats why they have 475 volt caps in there , i could always order 500 volt caps but just for testing and getting the set up and running i was going to double the caps using two 450 volt caps making it 900 volts handling , so that would be way over whats needed but the caps would be ok .
the dumont ra-103 , ra-103D and ra-110 all use a couple capacitors in series with 100k resistors on them , designers put that in to avoid a higher voltage capacitor.

mike
Reply With Quote
  #2  
Old 07-16-2013, 02:07 AM
ppppenguin's Avatar
ppppenguin ppppenguin is offline
VideoKarma Member
 
Join Date: Oct 2009
Location: London, UK
Posts: 466
In theory a pair of identical electrolytics will tend to balance the voltages across them fairly well due to leakage and the way the insulating layer is formed by the application of voltage. In practice as others have observed it can go badly wrong, especially if one cap dries out. I'd probably use bleeds even if this wasn's strictly needed. What value bleeds? The current needs to be large compared to leakage and small compared to what's being supplied to the load. This is total guesswork but I'd probably bleed about 1% of the load current.

If you are using non-electrolytics in series to increase the voltage rating then bleed resistors are essential. The problem in some case may be finding high enough values to keep the wasted current down. For example if you replace a 100n 5kV cap in a TV with mains EHT using 10x 1u 630V then 10M resistors will draw 50uA. This may be excessive.
__________________
www.borinsky.co.uk Jeffrey Borinsky www.becg.tv
Reply With Quote
  #3  
Old 07-16-2013, 11:07 AM
kx250rider's Avatar
kx250rider kx250rider is offline
REAL TVs have TUBES!
 
Join Date: Oct 2005
Location: Los Angeles & Dallas
Posts: 3,239
Quote:
Originally Posted by kramden66 View Post
In this set the electrolytics are 475 volts , i have a feeling that a 450 volt would be ok its just the start up voltage may go at or above 450 volts and then drop thats why they have 475 volt caps in there , i could always order 500 volt caps but just for testing and getting the set up and running i was going to double the caps using two 450 volt caps making it 900 volts handling , so that would be way over whats needed but the caps would be ok .
the dumont ra-103 , ra-103D and ra-110 all use a couple capacitors in series with 100k resistors on them , designers put that in to avoid a higher voltage capacitor.

mike
Or what I've done in certain cases with fast-warming B+ rectifier tubes or solid state B+ supplies, is to modify the B+ supply to include a delay relay, so as the filaments are all up before the B+ comes on. That shortens the duration (or eliminates) the unloaded high B+ surge on startup.

Charles
__________________
Collecting & restoring TVs in Los Angeles since age 10
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:47 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.