![]() |
|
|
|
#1
|
||||
|
||||
|
The wire on the HOT reminds me of those pens on chains at banks and post offices....Almost makes one envision the owner doing that to keep a crooked TV service guy from stealing his new output tube.
In your shoes I'd be tempted to leave the film caps and orange drops alone...The install ain't pretty, but (assuming no cold solder joints, and that the right replacements were installed) it should work fine.
__________________
Tom C. Zenith: The quality stays in EVEN after the name falls off! What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4 |
|
#2
|
|||
|
|||
|
progress
After cleanup of the previous work and replacement of a small number of caps there is a fairly good picture. The sound is weak though and there isn't that sweet quiet spot adjusting the quad detector coil. I think the signal is too strong. The contrast control seems to adjust the AGC in the IF's rather than the gain of the video output tube itself. The sync buzz is very prominent on graphics. Is there a known mod for this or do these predictas do well with strong signals and I should be looking elswhere?
|
|
#3
|
|||
|
|||
|
Hi All;
Cowboy, Your replacement work looks nice !! You have done a good job.. THANK YOU Marty |
|
#4
|
|||
|
|||
|
have you tried a new detector tube in the audio?
was the socket/trace ok? |
|
#5
|
||||
|
||||
|
Quote:
The 9L37 chassis used in 21" Predictas has a buzz control -- a potentiometer on the cathode of the audio detector -- where your set has a fixed resistor. If you feel like playing around, perhaps you could substitute a little pot there and see if it helps. Regarding the couplates (hybrids, networks), I guess it's a judgment call how many you want to replace, if any. I replaced one in my first Predicta and three in my second Predicta. These were replaced to cure problems that I observed after finishing a basic recap. The couplates that I didn't replace are still holding up years later; your mileage may vary, of course. One downside of shotgunning all of the couplates is that you'll make a crowded board even more crowded. You can read more about the second project (a Siesta) here: http://antiqueradio.org/PhilcoH3412L...Television.htm Phil Nelson Phil's Old Radios http://antiqueradio.org/index.html
Last edited by Phil Nelson; 05-12-2013 at 12:54 PM. |
| Audiokarma |
|
#6
|
||||
|
||||
|
I still need to get around to recapping mine
![]() Every time I see a Predicta thread I look at how easy others make it look and then I look at that box of parts from just radios but then I come to my senses and realize that I will start and realize that I should wait until I have more experience! I don't even have a tube tester :p
__________________
Lebe dein leben für dich selbst **Searching for any all tube or hybrid or color portable sets would consider some early solid state color too** Last edited by josephdaniel; 05-12-2013 at 03:05 PM. |
|
#7
|
|||
|
|||
|
Wrong resistor ?
This is a 11L43 chassis and Im working from a 10L42 schematic.
The screen grid resistor on the sound IF tube V5- 6EA8 is a 10k 1 watt but the diagram says 22k. The SG voltage is correct. Does someone know for sure what value this should be? I could just sub it but dislike soldering the pcb twice if it's for nothing. Still fighting for good sound. |
|
#8
|
||||
|
||||
|
For what it's worth, both the Sams schematic and the Philco factory schematic give 22K for that resistor. One says 80V for that pin, the other says 50V.
Phil Nelson |
|
#9
|
|||
|
|||
|
Sound issue on Predicta
I'm going to let it cook for a couple of days. I'm going to take a screen shot of the closing credits of Rock Center with their operating predicta on the shelf on this predicta.
|
![]() |
| Thread Tools | |
| Display Modes | |
|
|