Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-18-2012, 11:21 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
after replacing all the wax paper caps, I disconnected the can caps from the circuit (did not remove them from the chassis, just disconnected the terminals), and then used a vintage eye tube type cap tester. I started out on the lowest voltage leak test (25v IIRC) and would fix the test knob so the voltage would stay applied for an extended period. Most of the sections tested shorted (eye would not open), but over time the eye would open, when it did I would switch to the next higher voltage and repeat the process until the eye would fully open at the rated voltage.

I do not think the process would have worked as well if I had just used a variac for a lot of reasons that I don't want to take the time to document.

Variacs are useful tools but not for reforming.

Note, I am not saying this technique will always work or if it works how long the caps may last. In fact if I was repairing the set for someone I would not even bother, rather I would prob just put in new caps, it would be faster and prob safer, but I like to experiment and that was what this one was about.

Lastly I always put a fuse on the B+, and size it so it will blow quickly. If SS rectifier is used I will add a thermistor to allow for a fuse that is also just above the max operating current (inrush will blow a fuse too close to max).

Fusing should be done regardless of what is done about caps (reform or new), frankly new caps can fail, and in some cases I think a good old can cap may outlast some BS china cap.
Reply With Quote
  #2  
Old 12-18-2012, 11:48 AM
Geist Geist is offline
VideoKarma Member
 
Join Date: Dec 2012
Posts: 350
Hi All;
Dave can you tell me which Cap tester you have ?? I have a Solar Exam-eter Model CF.. I don't even know IF it works.. And I need to get the manual for it, I found the site the other day, but had ran out of printer paper, from before, so I did not print it..
THANK YOU Marty
Reply With Quote
  #3  
Old 12-18-2012, 12:02 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
Heath kit. Pretty much any old school cap tester should work, just need something that has a leak test that goes up high enough (think mine is 450v tops). Some testers use an eye tube, others a meter, the meter is prob better, I ofter will put a current meter in series with the cap to see exactly how much leakage there is (even with a fully open eye they will leak some). comparing to a new cap gives you an idea of how good an old one is. I recall there is a table somewhere that shows the allowable leakage in mA by capacity.
Reply With Quote
  #4  
Old 12-18-2012, 12:24 PM
Geist Geist is offline
VideoKarma Member
 
Join Date: Dec 2012
Posts: 350
Hi Dave;
Good old Heath Kit.. Thank You for the info..
THANK YOU Marty
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:50 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.