![]() |
|
|
|
#1
|
|||
|
|||
|
They seem to be all over the place, but most run hotter than I like. I have never had one that was under 100f after a long run like 1 hour or more.
I just got back from the surplus store. here is what I cobbled together, starting with some 1.5" ID foam pipe (used for insulation) I taped the seam, then using a soldering gun I melted out a square shape at the top so the square muffin would sit down into the pipe, the ID of the fan was about the same for a smooth transistion thru the duct. this is the top the fan will sit outside the fan cage. near the bottom of the pipe I cut a rounded slot that fits loosely over the tire, with enough room to allow the air to come out and flow over the tire. On the bottom I fashioned a foam plug that seals the bottom and conforms to the same cut out. With hindsight would have just fille it with some foam and then used the solder gun to cut the slot on the bottom, but it should work well enough to see if the idea has any merit. I have the fan running on a 9v battery (12vdc rated fan), its much smaller and less air than the larger muffin that I was using before, but will see if it works or not soon Oz is on now will run for about 30 min and check. this requres no mods to the cage but for a new top with a hole cut in it for the pipe and an outlet hole. since the top is swung open completly right now I will test it again with the fan/pipe out and the top wide open to see how much is fan and how much is just the open top. Last edited by DaveWM; 12-01-2012 at 01:43 PM. |
|
#2
|
|||
|
|||
|
I did buy some copper sheet as well to fashion a new top JIC it this works out. I really need to incorporate a couple slight bends to make it fit better as the flanges of the cage made it a bit of a tight fit coming out, but that should be an easy fix.
|
|
#3
|
|||
|
|||
|
being a man of science I think I see if I can zip tie on a thermistor to the fly on the core and take some resistance over time measurement to see if I can get a better feel for what works best.
If that does not work then she is a witch, burn her.... |
|
#4
|
||||
|
||||
|
Just be careful that the horizontal flyback pulse doesn't couple into the thermister leads, else the ohmmeter may get confused. And also don't create a sneak path for high voltage static discharge if you connect the DVM to it, there's a risk the meter may get zapped.
__________________
|
|
#5
|
|||
|
|||
|
dont think I will bother with the thermistor, the experiment has proven to me the only way to really keep it under 100f is a 3" muffin right at the base. I will prob just figure a way to mount it there and leave the cage off. I am not worried about fire as I never leave it running unattended, and I assume the x rays if any are still going to be shielded by the reaming 1/2 of the cage which effectively blocks the front (where I will be viewing).
While a 12 flybeck is not that hard to comeby my CTC-5 and CTC-9 are a bit harder. I was hoping to learn about best ways to add active cooling on this set but the real target are those. I may get motivated and build a cage with the bottom cut out for the larger fan. |
| Audiokarma |
|
#6
|
|||
|
|||
|
I used some very thin copper clad (both sided) material to fab up the cage. It was very easy as the material would bend sharply and you can burnish in a nice 90 degree bend. holes and cut outs are easy with some curved small scissors.
I folded in the tops about 1/2 inch and lap seamed with solder to hold its shape. I still need to fab up a top, but will wait on that until I test it out. cut a large round opening that puts the fan right at the side of the fly, used some silicone dabs in the corner of the fan to hold it in place, spaced up the fan just a bit from the copper (I am hoping that will keep the vibes from the fan from being amplified by the thin copper). I will take some pics tomorrow after the silicone has a chance to setup. I only have about 1 hr total fab time into it so if it does not work its no big loss. I will still have to make up a DC power supply, I think the filaments would be fine with a 1/2 wave and a 100uf filter cap. |
|
#7
|
|||
|
|||
|
I could not wait, the silicone had set up enough to hold the fan so I installed the cage and hooked up a 9v battery.
Its very quiet when the HV comes up the fan slows down, perhaps the fly is effecting it, like when the neon bulb lights up near the tire. the air is restricted by the close fitting back, I can put some spacers on the cage that should keep at least some clearance for air to get by, but its not ideal, and there is no real good way to mount it as one side sits next the horz out tube, one side is against the side wall and one side is on the back. I may have worked better if I just mounted it on top and aimed it down but I liked having the fan right up near the fly. |
![]() |
| Thread Tools | |
| Display Modes | |
|
|