Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-22-2012, 09:49 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Ceramic caps are fine for RF bypass duty, you see them in tuners, IF strips and sound IFs. They rarely go bad, so you shouldn't need to replace those. You usually avoid using ceramic caps in any tuned circuit (though some specially made ceramic caps, made to not drift much over temperature, are found in RF circuits, they are usually 5 to 100pF range). And avoid using ceramic caps in RC oscillators, like vertical osc circuits. Or horizontal oscilators, where the cap is part of the timing circuit.

Audiophiles avoid ceramic caps in audio amplifiers for hifi work, but if the amp in question is the usual 1 watt tube driving a 4 inch speaker in the side of the TV cabinet, ceramics will work well enough
__________________
Reply With Quote
  #2  
Old 04-25-2012, 05:28 AM
kvflyer kvflyer is offline
VideoKarma Member
 
Join Date: Nov 2006
Location: Fernandina Beach, FL
Posts: 1,132
Quote:
Originally Posted by wa2ise View Post
Ceramic caps are fine for RF bypass duty, you see them in tuners, IF strips and sound IFs. They rarely go bad, so you shouldn't need to replace those. You usually avoid using ceramic caps in any tuned circuit (though some specially made ceramic caps, made to not drift much over temperature, are found in RF circuits, they are usually 5 to 100pF range). And avoid using ceramic caps in RC oscillators, like vertical osc circuits. Or horizontal oscilators, where the cap is part of the timing circuit.

Audiophiles avoid ceramic caps in audio amplifiers for hifi work, but if the amp in question is the usual 1 watt tube driving a 4 inch speaker in the side of the TV cabinet, ceramics will work well enough
Hear hear! Well spoken and much too the point.
Reply With Quote
  #3  
Old 04-25-2012, 09:38 AM
tubesrule's Avatar
tubesrule tubesrule is offline
VideoKarma Member
 
Join Date: Jul 2004
Location: Michigan
Posts: 331
You need to be careful when referring to ceramic caps as there are different types. Class 1 ceramic caps can be used where film capacitors are used but are usually expensive. Class 1 ceramics (typically NPO/COG) are extremely stable, non-microphonic/piezoelectric with very low ESR and dissipation factors. In modern electronics I routinely design in Class 1 ceramics in sensitive areas such as coupling, timing/oscillators and PLL loop filters as surface mount film capacitors are expensive. The down side to Class 1 ceramics is they have very low volumetric efficiency so they are limited as to value/voltage rating, however values up to and beyond 0.01uF and 1KV are not unheard of. This still doesn't get us to the vertical coupling caps on an electrostatic set without multiple parts which is why films make sense in this application and why these parts work fine in the horizontal section.

Class 2 and 3 ceramics contain barium titanate which has a much higher volumetric efficiency which is why it is used, but is also what gives what people think of as ceramic capacitors a bad name.
Class 2 and 3 ceramics have very poor to extremely poor temperature stability, poor to very poor dissipation factors, poor aging and because barium titanate is piezoelectric, microphonics. You can take a typical Class 2 or 3 ceramic capacitor connected to a scope and by just tapping it, observe the voltage it generates.
Class 2 caps can be used in some coupling and filtering applications, but Class 3 are strictly designed for power supply filtering applications where they can replace tantalum and aluminum electrolytic caps.

There was at one time Class 4 ceramics with even worse parameters, but these are pretty much gone.

Darryl
__________________
Converters for obsolete standards:
www.tech-retro.com/aurora-design/legacy.html

Last edited by tubesrule; 04-25-2012 at 10:04 AM.
Reply With Quote
  #4  
Old 04-25-2012, 11:08 AM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by tubesrule View Post
...You can take a typical Class 2 or 3 ceramic capacitor connected to a scope and by just tapping it, observe the voltage it generates.
You can also hear the capacitor 'click' from a voltage spike applied across it (as in the breakdown test on an old style cap tester).
Reply With Quote
  #5  
Old 04-25-2012, 11:13 AM
tubesrule's Avatar
tubesrule tubesrule is offline
VideoKarma Member
 
Join Date: Jul 2004
Location: Michigan
Posts: 331
Quote:
Originally Posted by old_coot88 View Post
You can also hear the capacitor 'click' from a voltage spike applied across it (as in the breakdown test on an old style cap tester).
True, that's why there are ceramic phonograph cartridges and ceramic speakers. They can be used both ways. Not such a great thing in a capacitor though

Darryl
__________________
Converters for obsolete standards:
www.tech-retro.com/aurora-design/legacy.html
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:13 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.