Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-04-2012, 08:23 PM
vts1134's Avatar
vts1134 vts1134 is offline
Looking For Time
 
Join Date: Apr 2011
Location: Pittsburgh, PA
Posts: 1,534
Made a bit of progress since the last post, but I moved backwards in the meantime. While I was troubleshooting the vertical problem I turned the set upright and after a couple of snap crackle pops and the high voltage went away. I was perplexed and couldn't tell where the sound came from so I went back to the schematic. I soon realized that I missed four caps that were hiding inside and underneath the high voltage cage. There were two paper and two bumble bee caps hiding from me. After replacing the offending caps the high voltage returned to normal.
I also managed to find the vertical problem. The offending problem was a capacitor lead that was left behind by a previous repair had shifted into a dead short to the pin next to it on the vertical oscillator. It was obscured enough that I didn't spot it when I looked over the set before firing it up the first time. It kind of brings me to this question. When I replace parts in a set I remove the old part completely and install the new part through and then around the original mounting hole. Most repairs I find in these sets are cut the old part out and solder the new part in next to the old one. Do most of you also run into similar shoddy work when you restore a set?
Any way on to where we stand now. I've got a fairly good picture but I've got kind of a wierd problem. With my horizontal running in frequency my picture is not full width, but when I adjust the horizontal out of fequency the picture is full width.





Can any one give me a possible explanation for this one?
Reply With Quote
  #2  
Old 04-09-2012, 09:41 PM
earlyfilm's Avatar
earlyfilm earlyfilm is offline
Eternal Member
 
Join Date: Jun 2011
Location: Culpeper, VA
Posts: 527
Quote:
Originally Posted by vts1134 View Post
When I replace parts in a set I remove the old part completely and install the new part through and then around the original mounting hole. Most repairs I find in these sets are cut the old part out and solder the new part in next to the old one. Do most of you also run into similar shoddy work when you restore a set?
Not necessarily shoddy work, but they were complying with the law.

Back then one usually had to give an estimate before the set was repaired and if the customer said "no" you had to remove all your new parts and put the originals back in. You could still charge for the labor. This method enabled that.

However, as soon as the customer OKed the repair most shops just stuck the chassis back in the cabinet leaving both parts in, especially if it was a walk-in with the customer standing there with the money in his hand.

James
Reply With Quote
  #3  
Old 08-12-2012, 04:43 PM
cbenham's Avatar
cbenham cbenham is offline
VideoKarma Member
 
Join Date: May 2006
Posts: 471
Quote:
Originally Posted by vts1134 View Post
When I replace parts in a set I remove the old part completely and install the new part through and then around the original mounting hole.
I fully agree with your practice of completely removing the old part and properly installing the new one. This is the best and most approved way.

However, in several instances I have had bad luck attempting this because the tube socket pin breaks off while removing the old part wires.

This leads to finding a replacement socket at a hamfest and replacing the bad one. What a $#$&%$&# PAIN!

If I suspect the set has lots of previous poor repair work, and the sockets look well worn, I clean and scrape the two existing part wires after clipping the part out and wrap the wires of the replacement part carefully around them and solder them really well. The cleaning and scraping is important for a proper connection. Then I reflow the solder on the pin as well.

I've never had a repair go 'bad' using this method and I've not broken any more socket pins either.

Remember, desperate people do desperate things!

Cliff
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:02 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.