Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 03-03-2012, 06:12 PM
stromberg6's Avatar
stromberg6 stromberg6 is offline
VideoKarma Member
 
Join Date: Sep 2004
Location: Ellington,CT
Posts: 465
Smile

Hi Bob, I'm curious to know how you resolved the dropping resistor situation. I also would have inserted it between the 4.5 amp fuse and the rectifiers, but upon looking at the schematic for my 4, I see that it would not be the best place to put it. I too am having voltage drop trouble with the original rectifiers, and need to replace them with 1N4007's, or equiv. B+ is about 345-350, not the 380 specified in the RCA lit, and when I crank up the variac the improvement in the pic is notable.
Thanks!
Kevin G.
__________________
stromberg6
Reply With Quote
  #2  
Old 03-03-2012, 10:06 PM
ohohyodafarted's Avatar
ohohyodafarted ohohyodafarted is offline
Bob Galanter
 
Join Date: Sep 2005
Location: Whitefish Bay, Wi (Milwaukee)
Posts: 1,080
Quote:
Originally Posted by stromberg6 View Post
Hi Bob, I'm curious to know how you resolved the dropping resistor situation. I also would have inserted it between the 4.5 amp fuse and the rectifiers, but upon looking at the schematic for my 4, I see that it would not be the best place to put it. I too am having voltage drop trouble with the original rectifiers, and need to replace them with 1N4007's, or equiv. B+ is about 345-350, not the 380 specified in the RCA lit, and when I crank up the variac the improvement in the pic is notable.
Thanks!
Kevin G.
Kevin,

I will have to get back to you in a couple days. I am going to relocate the dropping resistor in the lead that connects the out going leg of one of the half wave diodes to the main filter caps. I will post a drawing with the placement and the value of the dropping resistor when it is finished. That said, replacing the inefficient sleniums will bring back your B+ to a much higher level. It will probably be too high like mine is now.

I have been nusring a very nasty case of the flu for 4 days now and I think I will be back up and around in another day or so. Watch for a future post.
__________________
Vacuum tubes are used in Wisconsin to help heat your house.

New Web Site under developement
ME http://AntiqueTvGuy.com
Reply With Quote
  #3  
Old 03-14-2012, 01:10 PM
ohohyodafarted's Avatar
ohohyodafarted ohohyodafarted is offline
Bob Galanter
 
Join Date: Sep 2005
Location: Whitefish Bay, Wi (Milwaukee)
Posts: 1,080
Quote:
Originally Posted by stromberg6 View Post
Hi Bob, I'm curious to know how you resolved the dropping resistor situation. I also would have inserted it between the 4.5 amp fuse and the rectifiers, but upon looking at the schematic for my 4, I see that it would not be the best place to put it. I too am having voltage drop trouble with the original rectifiers, and need to replace them with 1N4007's, or equiv. B+ is about 345-350, not the 380 specified in the RCA lit, and when I crank up the variac the improvement in the pic is notable.
Thanks!
Kevin G.
Sorry it took so long to get back to you Kevin. I have had the flu and a million things to do and I just got to figuring out the placement and value of the resistor needed.

This is what I have done. Using clip leads I inserted a 1K 50 watt wire wound pot into the power supply circuit. The best place to insert the droping resistor is on either one of the leads of the power supply choke. I chose this location because it is the best place to insert and have the droping resistror effect all of the various power supply voltages.

While adjusting the 1K 50W pot, I monitored the B+ supply voltage and when I reached 350V (the specification on the Sams schematic) I recorded the voltage across the pot and the current through the pot. I dropped 72 volts and had 440ma currrent. I calculated about 32 watts of heat energy will be generated. Then I disconnected the pot and measured the resistance. 150 ohms. I have ordered some Vishay 50W 150 Ohm Aluminum clad power resistors from Mouser. Mouser Part# 71-RH50-150 at $4.67 each. I will mount the resistor somewhere on the top of the chassis where the heat will be easily disipated.

If you want to go with the 380v B+ as specified in the RCA print, then these values are what you will need. 70 ohm 20 watt, gives me 380v B+ in my set. My set seems to be functioning about the same at either B+ voltage. I get a nice full bright raster at either 350v or 380v.

If you replace the original stack rectifiers with 1A 1000piv diodes I would guess you will need to drop a similar amount of B+ voltage to get the supply voltages back within specification. Good luck, and I will post the photos of the mod in a couple of weeks after the new resistors arrive and I install them, so you can see how I did it.
__________________
Vacuum tubes are used in Wisconsin to help heat your house.

New Web Site under developement
ME http://AntiqueTvGuy.com

Last edited by ohohyodafarted; 03-14-2012 at 01:48 PM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:01 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.