Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-21-2012, 11:11 AM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by Unimatic1140 View Post
So as for the CRT socket:
Pin 2 +0.6
That's the control grid (G1). It should rise to around 100-115V as you advance brightness to maximum. Does it?
In other words, its bias relationship to the cathode (pin 11) should be at or near 0V at max brightness.

What is the voltage directly at the brt.control wiper as you turn the control stop-to-stop? What is the voltage at the top (hot) terminal lug of the control? Just for the heck of it, check for continuity in the wire going from the wiper to pin 2 (just on the chance there might be a break in that wire).

Quote:
Pin 10 437 (sams says should be 400)
Pin 11 116 (sams says should be 115)

Last edited by old_coot88; 02-21-2012 at 12:25 PM.
Reply With Quote
  #2  
Old 02-21-2012, 09:12 PM
Unimatic1140's Avatar
Unimatic1140 Unimatic1140 is offline
VideoKarma Member
 
Join Date: Jun 2002
Location: Minneapolis
Posts: 70
Quote:
Originally Posted by old_coot88 View Post
That's the control grid (G1). It should rise to around 100-115V as you advance brightness to maximum. Does it?
In other words, its bias relationship to the cathode (pin 11) should be at or near 0V at max brightness.

What is the voltage directly at the brt.control wiper as you turn the control stop-to-stop? What is the voltage at the top (hot) terminal lug of the control? Just for the heck of it, check for continuity in the wire going from the wiper to pin 2 (just on the chance there might be a break in that wire).
Thanks again everyone here is what I found...

on the far end of the 100K resister (R35) it reads 330 volts, after it crosses R35 the voltage drops to 0.69 volts which is the input to the Brightness Control. The wiper of the brightness control seems to vary the voltage from stop-to-stop at 0.04 volts at min to 0.67 volts with the dial turned to max and this is what is output to Pin 2 of the picture tube cap. The continuity of the wire is just fine, but always good to check! Old_Coot88 are you saying with the brightness turned up Pin 2 the output of the wiper should be 100 to 115volts? If so 0.69 volts is obviously way off.
Reply With Quote
  #3  
Old 02-21-2012, 09:34 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Try disconnecting R35 from the top lug of the brt.control and see if it's open or gone 'waaay high in value. If R35 is OK, measure from the top of the brt.control to ground and see if it's shorted or very low resistance. Both R35 and the control should read 100K according to the schematic.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:02 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.