Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-21-2011, 07:02 PM
Electronic M's Avatar
Electronic M Electronic M is offline
M is for Memory
 
Join Date: Jan 2011
Location: Pewaukee/Delafield Wi
Posts: 15,496
Most focus coils can not only be moved back and fourth, but also tilted to keep good focus and eliminate corner shadows.

If the Retrace lines consist of dashes come and go in the top to the screen and they don't run the full distance from side to side that it is porbably the copy protection signal from the tape or DVD that you are seeing. You can buy devices that will remove the offending copy protect signal if you want.

I'm not familiar with early admirals, but can offer that some vintage sets of some brands pick off the audio signal after the contrast control and may have their sound affected by it.

Hope this helps.
__________________
Tom C.

Zenith: The quality stays in EVEN after the name falls off!
What I want. --> http://www.videokarma.org/showpost.p...62&postcount=4
Reply With Quote
  #2  
Old 10-21-2011, 07:09 PM
leadlike's Avatar
leadlike leadlike is offline
VideoKarma Member
 
Join Date: Apr 2008
Location: Lancaster, Pa
Posts: 956
On early Admirals, the contrast control really is a signal strength control, a potentiometer on the front end circuits. I had one that would do the same thing as you turned the contrast down, until you had no signal, only snow. Turning the control up all the way produced overloaded video and blasting sound.

Depending on your video source, you may be viewing copyguard lines on your video, especially if they fade in and out periodically.
Reply With Quote
  #3  
Old 10-21-2011, 07:33 PM
zenith2134's Avatar
zenith2134 zenith2134 is offline
VideoKarma Member
 
Join Date: Feb 2005
Location: UTC -4
Posts: 2,546
Yes, in my service manual for 1952 Admiral 21F1 chassis explains that the contrast control is an additonal gain level with the varying level fed into the video tubes.
Reply With Quote
  #4  
Old 10-21-2011, 07:35 PM
UberVacTuber's Avatar
UberVacTuber UberVacTuber is offline
Hey, I can fix that!
 
Join Date: Nov 2008
Location: Royal Oak, MI
Posts: 58
Quote:
Originally Posted by Electronic M View Post
If the Retrace lines consist of dashes come and go in the top to the screen and they don't run the full distance from side to side that it is porbably the copy protection signal from the tape or DVD that you are seeing. You can buy devices that will remove the offending copy protect signal if you want.
Yep, I've seen a small black bar at the top of the screen with those little dashes that come and go and move around. However, these are thin white lines that are on a slant and are spaced about an inch apart. I took a photo of what I'm talking about (On the screen is a shot of LeMans with Steve McQueen. It's in widescreen, so the aspect ratio is supposed to be off):



You can see the little dashes at the top. The diagonal lines can be made to jitter with the Vertical Hold adjuster. Even when you turn the Contrast all the way down, those lines are still there, just superimposed on a gray screen.
Reply With Quote
  #5  
Old 10-21-2011, 07:45 PM
zenith2134's Avatar
zenith2134 zenith2134 is offline
VideoKarma Member
 
Join Date: Feb 2005
Location: UTC -4
Posts: 2,546
...the copy-protection is quite visible during retrace/vertical blanking on all my sets when you look at the scope, but is only visible 'on screen' on some of them. (btw, is this Macrovision on dvd or something else.)
I think a lot depends on the set's video output circuitry, many old tv's tend to blank this out along with the rest in the VBI but others have obnoxious lines at the top.
Reply With Quote
Audiokarma
  #6  
Old 10-22-2011, 09:55 AM
earlyfilm's Avatar
earlyfilm earlyfilm is offline
Eternal Member
 
Join Date: Jun 2011
Location: Culpeper, VA
Posts: 527
Quote:
Originally Posted by UberVacTuber View Post
However, these are thin white lines that are on a slant and are spaced about an inch apart.
Your picture shows two problems.

First is the copy protection that has been mentioned.

The other problem is retrace showing.

Before you do the mentioned added capacitor, check the grid coupling capacitors on your video output tube for leakage. Check either by substitution with a known capacitor, or with a battery (at least 15 volts, better higher) in series with the suspected capacitor. The voltmeter reading should drop to zero in a few seconds if the cap is good. Bad ones go to almost zero, but never to zero.

It usually is not the first video, but it does no harm to check that one the same way while doing the other.

James
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:45 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.