Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early Color Television

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 08-11-2011, 11:01 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
IIRC, Seleniums have a forward voltage drop of about 5 to 9 volts, and a silicon rectifier has a forward voltage drop of .7 to .9 volts.

Georg Simon Ohm's little contribution says that E=IxR, and we need to drop approximately 7 volts (somewhere in the middle of the selenium voltage drop range).

I'm assuming a 21-CT-55 would draw about 450 watts from the power line at 115/117V, so the current draw would be about 3 Amperes. Not all of that is B+ current, so let's say (worst case) the B+ current is 1 Ampere. It is more likely in the 550-800mA range, I suppose.

Now that we know the current and voltage, getting to the resistance needed to drop that voltage is simple Algebra 0.5:

R=E/I, so 7/1 gives you about 7 ohms, well within the adjustable range of Bob's 7.5 ohm resistor.

My calculations/explanations are full of assumptions, and are VERY open to correction.....I just did the same math for an old 6L6-based amp, and it worked well. Your mileage may vary. Fuses are a must, I might add.

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #2  
Old 08-12-2011, 05:38 PM
ohohyodafarted's Avatar
ohohyodafarted ohohyodafarted is offline
Bob Galanter
 
Join Date: Sep 2005
Location: Whitefish Bay, Wi (Milwaukee)
Posts: 1,080
Nick,

The ctc4 has a 10 ohm 25W resistor in the ac side between the common lead of the diodes and 4.5A power supply fuse. The other power resistor you saw on my CTC4 chassis is original to the chassis and is somewhere else in the power supply ckt.
__________________
Vacuum tubes are used in Wisconsin to help heat your house.

New Web Site under developement
ME http://AntiqueTvGuy.com
Reply With Quote
  #3  
Old 08-12-2011, 10:06 PM
old_tv_nut's Avatar
old_tv_nut old_tv_nut is offline
See yourself on Color TV!
 
Join Date: Jul 2004
Location: Rancho Sahuarita
Posts: 7,815
Quote:
Originally Posted by Findm-Keepm View Post
IIRC, Seleniums have a forward voltage drop of about 5 to 9 volts, and a silicon rectifier has a forward voltage drop of .7 to .9 volts.

Georg Simon Ohm's little contribution says that E=IxR, and we need to drop approximately 7 volts (somewhere in the middle of the selenium voltage drop range).

I'm assuming a 21-CT-55 would draw about 450 watts from the power line at 115/117V, so the current draw would be about 3 Amperes. Not all of that is B+ current, so let's say (worst case) the B+ current is 1 Ampere. It is more likely in the 550-800mA range, I suppose.

Now that we know the current and voltage, getting to the resistance needed to drop that voltage is simple Algebra 0.5:

R=E/I, so 7/1 gives you about 7 ohms, well within the adjustable range of Bob's 7.5 ohm resistor.

My calculations/explanations are full of assumptions, and are VERY open to correction.....I just did the same math for an old 6L6-based amp, and it worked well. Your mileage may vary. Fuses are a must, I might add.

Cheers,
Not a good idea to calculate the resistance needed based on the DC (average) current. It might be right but probably won't be. The voltage drop actually depends on the instantaneous charging current, and that depends on the size of the filter caps and how much ripple is on those caps.
Reply With Quote
  #4  
Old 08-12-2011, 11:03 PM
Phil Nelson's Avatar
Phil Nelson Phil Nelson is offline
VideoKarma Member
 
Join Date: Jan 2006
Posts: 4,030
Why not just try different values until the B+ is what you want?

Phil Nelson
Reply With Quote
  #5  
Old 08-12-2011, 11:43 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Quote:
Not a good idea to calculate the resistance needed based on the DC (average) current. It might be right but probably won't be. The voltage drop actually depends on the instantaneous charging current, and that depends on the size of the filter caps and how much ripple is on those caps.


Why not just try different values until the B+ is what you want?

Phil Nelson
I believe that is what Wayne was implying. The overall forward resistance of the silicon diode plus added resistance must match the forward resistance of the original selenium rectifier. This should maintain the instantaneous charging current.

The net result of the properly chosen extra resistor will ensure the same ripple. Hence the resistor is chosen to match the original B+ voltage.

Terry
Reply With Quote
Audiokarma
  #6  
Old 08-24-2011, 01:02 AM
vintagecollect's Avatar
vintagecollect vintagecollect is offline
VideoKarma Member
 
Join Date: Jul 2005
Posts: 658
those seleniums seem never to last long. I just used newer diodes in mine too and kept sels. for looks
__________________
1977 Zenith Chromacolor II
A Very Modern Zenith
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:26 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.