![]() |
|
|
|
#1
|
|||
|
|||
|
Hokay. Now it makes a lot more sense. What threw me was the 6L6 being designated "oscillator". So i hadn't bothered to eyeball further back into that H.sync subchassis. Turns out it actually uses a pretty decent phase comparator circuit, rather than "direct injection" of sync into the 6L6 as i first thought.
But still wondering how the flyback is kept from ringing without a damper.From the FWIW department, here's a few thoughts pertaining to the HV.. The three 680K 1W resistors in series sure look to be a post hoc engineering fudgery to limit the HV. As mentioned before, they form the lower leg of a voltage divider. The capacitive reactance of the 500pf 10KV cap forms the uppermost "resistor" of the string. If t'were me, i would open the lower string and insert a fourth resistor and experiment with its value, starting with 680K 1W. Finally, if it looks to be warranted, maybe open the string entirely and see what the HV does. If the HV still seems a little "soft" (bloomy), i would first try a 680K 1W across the aforementioned cap and then experiment with values, to see if it'll stiffen the supply up (ie., give it better regulation, making the pic less bloomy). And those four 20 meg resistors in series, totaling 80 meg, serve no obvious function other than to bleed the charge off the CRT when the set is turned off. They could be dispensed with altogether (IMHO), as most sets never used a bleeder at all on the CRT anode. oc |
|
#2
|
||||
|
||||
|
Quote:
Quote:
Phil Nelson |
|
#3
|
|||
|
|||
|
No, just open the string and insert a fourth resistor in series with the other three. Probably the bottom end would be the best place to open it because that's where it's at the lowest potential.
Quote:
|
|
#4
|
||||
|
||||
|
Phil,
I was looking at the schematic and I see the horizontal hold is called "framing". The control called "horizontal sync" seems to me would help frame the image. Very quaint nomenclature on this set overall. Curious. On the AFC subchassis, the 6K6 is indeed the horizontal oscillator, the 6AC7 reactance control and the 6AL5 is the horizontal phase detector. The set up is almost identical to the classic RCA Synchrolock horizontal AFC. Perhaps the subchassis was a later production add on when they found the 6L6 as an oscillator/output combination wasn't up to snuff? Perhaps Farnsworth bit the bullet and later obtained a licence from RCA to use this circuit? Who knows? What I find particularly interesting is its almost prewar design using so many octal tubes. Great work. I am especially impressed by your CRT fix! Terry |
|
#5
|
||||
|
||||
|
Yah, I was curious about the framing control, too. In fact, the horizontal sync control does what you'd normally expect: it controls the horizontal until you lose sync at one end of its range or the other.
The framing control has the same effect as (drumroll . . .) the horizontal centering control. Turning it simply shifts the entire image a bit left or right. Don't ask me why they wanted this control in front -- or wanted it at all, since it acts like a second centering control, unless it's a leftover from some earlier design that wasn't as stable. My favorite quaint term is "beam relaxor transformer" for flyback. I wonder where they came up with that! Phil Nelson |
| Audiokarma |
|
#6
|
||||
|
||||
|
Quote:
Oh well, you can't learn everything at once.Phil Nelson |
|
#7
|
||||
|
||||
|
Well, the cabinet's refinished and the audio & picture are pretty peachy. I'd call this project done except for the imperfect horizontal linearity seen in the most recent photo.
This set has no horizontal linearity control, damper tube, or drive control, so there ain't much to play with apart from the width & centering. This degree of non-linearity isn't a big deal when you're watching a movie, but this is not the only TV I've had with exactly the same issue -- left side too wide despite all adjustments -- so I wonder what the deal is. Phil Nelson |
|
#8
|
||||
|
||||
|
T'aint perfect, but every project must end, and 3.5 months is long enough for this one. Here's an article, with a few items not covered in this thread:
http://antiqueradio.org/CapehartFarn...Television.htm Thanks, as always, for the advice & encouragement. Phil Nelson Phil's Old Radios http://antiqueradio.org/index.html
Last edited by Phil Nelson; 09-16-2011 at 08:46 PM. |
|
#9
|
|||
|
|||
|
Wow, another engaging, informative and thoroughly enjoyable resto saga by Phil. Good to learn some of the arcana behind the Capehart-Farnsworth symbiosis. It's a privilege to have played a small part in helping the project along, and to have vicariously "worked on" an actual set bearing some of old Philo's 'novel' pre-standardization circuit features. Interestingly, just an easy walk from an apt. building i manage is Philo's old lab at 202 Green Street, SF. http://www.noehill.com/sf/landmarks/cal0941.asp
|
![]() |
| Thread Tools | |
| Display Modes | |
|
|