![]() |
|
|
|
#1
|
||||
|
||||
|
Quote:
The tough part of all of this is making 2 custom delay lines, because with component the color gets to the CRT before the luma does. Blue is less noticable than red is, since there's a greater proportion of red in almost every scene. What's needed are a pair of properly terminated delay lines, whose delay is custom tailored to the set in question. Since there will be a voltage drop across the line, another stage of amplification will likely be needed. I'm experimenting with 6GH8 (yeah yeah, they are laying around) pentode sections to preamplify the signal before it's sent through the line, but it's not an exact science. Ghosting is a big problem, as is crosstalk. The entire thing must be designed correctly or the result will be horrible. But if and when I get it right, the result will be nothing less than spectacular. Perfect convergence, luma to 4Mhz with no dot crawl, and color with digital accuracy. It will rival the picture quality of any NTSC set, including my CT55. Pretty ridiculous for a set I got for free.
__________________
Evolution... |
|
#2
|
||||
|
||||
|
Seems to me that an electronic adjustable delay would be necessary. The higher resolution will mean that the delay is more critical. Hence I figure it would have to be adjustable for best results.
Terry |
|
#3
|
||||
|
||||
|
Componant differential delay
Quote:
A properly designed component video monitor will in turn process the three input analogs in identical full 5mhz BW and apply them as RGB to identical full BW CRT driver amps. Since Y, Pr, Pb and resulting RGB are processed the same there is no need for any delay lines, analog or digital to correct differential delay. Last edited by Tomcomm; 10-26-2015 at 04:11 PM. |
|
#4
|
||||
|
||||
|
The extra delay compensation was implied for your monitor. I suspect you would want to have a low pass filter in the luma and chroma paths. But then maybe that will not be necessary if the filtering is done at the source.
Or did I miss something? Terry |
|
#5
|
||||
|
||||
|
Quote:
OK, I must be wrong then. Let me know how that works out for you. ![]() You still have a luma delay, don't you? What do you think that does to the coincidence of luma and chroma at the CRT? Trust me, it's not as simple as removing the luma delay, either. There are time shifts happening in the luma channel as well as chroma, if you don't do anything it's not gonna end up at the same place at the same time.
__________________
Evolution... |
| Audiokarma |
|
#6
|
||||
|
||||
|
Quote:
I'll try again! ............The DVD player outputs R-Y as rP and B-Y as bP in perfect time registry with each other and the luma/sync as Y. The DAs that make the Y, rP and bP have responses well greater than 5MHZ at the DVD outputs. If the three coax cables leading to the CTC2B monitor are matched, perfect time registry is retained as they enter directly into the new Component to RGB converter piggy-back boards. The analog processing on these converter boards uses all ultra high speed SS video op-amps spec'd at 400mhz, 400V/us, 25ns rise time.The only signal the original CTC2B works on is the Y luma/sync and this goes direct to the sync separators and retrace blankers no place else. The RGB videos from the converter boards go directly to the original red, green and blue full BW CRT driver board's first stage grids. So is the possibility for time registry errors existing at the CRT socket real? I think not. Last edited by Tomcomm; 07-25-2011 at 06:20 PM. |
|
#7
|
||||
|
||||
|
Quote:
![]() It would seem to me this may be a recipe for alias artifacts. Then again, I may be wrong. I would consider filtering at least to ITU R601 specifications eg approximately 5.5 MHz for luma and 2.75 MHz for chroma. ![]() Terry |
|
#8
|
||||
|
||||
|
Quote:
__________________
stromberg6 |
|
#9
|
||||
|
||||
|
That last post got screwed up in sequence, but I think you get the message.
Kevin
__________________
stromberg6 |
![]() |
| Thread Tools | |
| Display Modes | |
|
|