Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-13-2011, 12:57 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
I assume you don't mean the evacuation tip is broken. If it's intact there's still a chance the 12LP4 is good.

Elves probably started to repair the base for you and got chased away by your Dachshund. Actually, if he did knock it off he did you a favor because it couldn't have been soldered on very well.

One method I've read on this forum is to attach small gauge wire to the leads to make it easier to thread the socket back on.

John

Quote:
Originally Posted by benman94 View Post
I am currently in the process of (attempting) to restore a 1949 RCA T-100. When I got the set home, pulled out the chassis, and started testing and marking off weak tubes, I noticed that the black plastic base of the CRT (the part with all the pins) was coming loose. I went to bed, and woke up this morning to find the black base sitting on the chassis and what I presume to be the evacuation tip where the base was late last night. I have an inkling my Dachshund is to blame . . . Anyway, the 5 leads from the tube (Numbers 1, 2, 10, 11, and 12) are still intact. In fact, I have about a solid 1 to 1.5 inches to work with. If I were to rewire the leads to the base, and then reattach the base with RTV silicone or something similar, is there a chance that the tube could be salvaged?

Thanks,
Benny
Reply With Quote
  #2  
Old 06-13-2011, 01:26 PM
Mal Fuller Mal Fuller is offline
VideoKarma Member
 
Join Date: Jun 2011
Posts: 110
Removing all the solder from the pins on the base is a necessary first step in saving your 12LP4.
If you heat the pins one at a time and then quickly smack the base on your work bench while the solder is still molten, this will effectively remove all the solder from each pin.
You should be able to carefully finesse each wire back into the base. Glue the base to the neck making sure each wire is fully inserted in each pin, I use Elmer's. Allow 24 hours for the glue to set.
Finally, with the tube face-down, solder each pin, removing your iron the instant the solder starts to flow.
Good luck.
Reply With Quote
  #3  
Old 06-13-2011, 02:22 PM
pearsonk pearsonk is offline
VideoKarma Member
 
Join Date: Mar 2006
Posts: 132
I think the T-100 uses a 10BP4, the T-120 uses the 12lp4.
Same base pins.
Reply With Quote
  #4  
Old 06-13-2011, 04:06 PM
Steve McVoy's Avatar
Steve McVoy Steve McVoy is offline
VideoKarma Member
 
Join Date: Oct 2002
Location: Columbus, Ohio
Posts: 1,619
An easier way to do this is to use some fine wire, like strands from a line cord. Solder a 6 inch length of a strand to the end of each lead coming from the CRT. Make sure the solder joint is small enough to go through the holes in the pins on the base. Now you can easily thread each strand through the appropriate pin. Once all are threaded, put some glue on the base, and pull the base onto the tube and solder each pin. As you do this, you can remove the strand.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:53 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.