Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 05-25-2011, 03:51 PM
vts1134's Avatar
vts1134 vts1134 is offline
Looking For Time
 
Join Date: Apr 2011
Location: Pittsburgh, PA
Posts: 1,534
Quote:
Originally Posted by old_coot88 View Post
Arr. Now we're cookin'. First assuming the output transformer and yoke coils have proved good, I wouldn't worry about the oscillator just yet, but first prove whether the output stage is working or not. Just inject some AC at the control grid (pin 5) of the 6V6. No need to disconnect anything, since everything 'upstream' is high impedance and DC-isolated by C50. Just run a jumper from pin 7 (heater) to pin 5. That'll put 6.3VAC directly on the grid, which should give a few inches of deflection (and it should vary somewhat with the linearity adjustment). If it does, that would indicate the output stage is working, and the failure lies upstream in the osc. area.
oc
Should I get a few inches of deflection total? or a few inches more deflection than I have already, which is already a few inches?
Reply With Quote
  #2  
Old 05-25-2011, 04:56 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by vts1134 View Post
Should I get a few inches of deflection total? or a few inches more deflection than I have already, which is already a few inches?
A few inches total, since all the grid will be "seeing" is the 6.3VAC. Also, before doing this, try grounding pin 5. You should get a flat line. Then do the 6.3 jumper trick. How does this deflection compare with what you already had?
Reply With Quote
  #3  
Old 05-26-2011, 08:03 AM
vts1134's Avatar
vts1134 vts1134 is offline
Looking For Time
 
Join Date: Apr 2011
Location: Pittsburgh, PA
Posts: 1,534
OC- Grounding pin 5 did indeed give me a flat line. Jumping pin 5 to pin 7 gave me a lot of deflection as you can see below. The two pictures below display the range I got from adjusting the linearity adjustment.





Very exciting to see something different! Also kind of interesting to see 60hertz through the second picture, which I only noticed on the picture and not looking at the set itself. Thanks so much to all of you for all the help again, I'm having such a blast with this!
Reply With Quote
  #4  
Old 05-26-2011, 09:35 AM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Hey cool. Now in one fell swoop you've proved that the output stage, transformer and yoke are all good, and the failure lies back in the osc. area. Basic isolation technique 101.

Last edited by old_coot88; 05-26-2011 at 11:17 AM. Reason: typo. Duh.
Reply With Quote
  #5  
Old 05-30-2011, 01:42 PM
vts1134's Avatar
vts1134 vts1134 is offline
Looking For Time
 
Join Date: Apr 2011
Location: Pittsburgh, PA
Posts: 1,534
I spent some time looking over the schematic to get familiar with things down stream from the vertical output stage. I traced each connection from point to point on the schematic and on the set itself and found my first mistake. I had connected the secondary of T2 to the wrong place. I connected it correctly and got this.

I also found the the ion trap was a bit out of place so I tried to align it as much as I could by site. I also adjusted the vertical controls to see if I could get an aligned picture but the picture above is as good as I could get it. I'm not sure if you can tell by the picture but the bottom of the picture is brighter than the top, and the left hand side of the screen is brighter than right. Any ideas on where to head next?
Reply With Quote
Audiokarma
  #6  
Old 05-30-2011, 01:56 PM
VintagePC's Avatar
VintagePC VintagePC is offline
Tube bug got me 05/2010
 
Join Date: May 2010
Posts: 535
Looks to me as though something is clamping the vertical sweep wave... i.e. it's rounded off on the bottom instead of a nice sawtooth.I'd be tempted to say it's a passive component (resistor, capacitor) that's the culprit, but if that's the case, you'd see it at the top of the sweep too.

Does anything happen if you adjust the vertical centering control, and if so, can you bring the top edge of the raster in to view?
Reply With Quote
  #7  
Old 05-30-2011, 03:55 PM
vts1134's Avatar
vts1134 vts1134 is offline
Looking For Time
 
Join Date: Apr 2011
Location: Pittsburgh, PA
Posts: 1,534
I don't know where the vertical centering control is on my set. I don't see mention of it in the schematics.
Reply With Quote
  #8  
Old 05-30-2011, 04:01 PM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Quote:
Originally Posted by vts1134 View Post
....I also adjusted the vertical controls to see if I could get an aligned picture but the picture above is as good as I could get it. I'm not sure if you can tell by the picture but the bottom of the picture is brighter than the top... Any ideas on where to head next?
Try jumping a known-good electrolytic across C1 (the 100mf one going to the cathode [pin 8] of the 6V6). That's exactly the effect you'd see if that cap were open. oc
Reply With Quote
  #9  
Old 05-31-2011, 08:19 AM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
The bottom is brighter than the top because the vertical linearity is way off. It could be an adjustment, or a symptom of another problem.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:18 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.