Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 02-28-2011, 01:12 AM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by Penthode View Post
But the solution for the DTV OTA box is way too cool! I suppose the key is finding the NTSC encoder. How did you locate the encoder?

I have a Zenith box
Problem with the Zenith and most other boxes is that the NTSC encoder likely resides buried deep inside a chip, where you can't get at the luma and chroma separately. The reason I could modify the Channel Master box was that it had an S video jack. That meant that the luma could be accessed separately from the chroma.
__________________
Reply With Quote
  #2  
Old 03-01-2011, 10:57 PM
Penthode's Avatar
Penthode Penthode is offline
VideoKarma Member
 
Join Date: Jun 2009
Location: Kitchener/Waterloo Ontario Canada
Posts: 1,463
Thanks for the replys. I do not want to curtail the bandwidth to 3MHz. I have visitors look at my late 40's or early 50's RCA and cannot believe how sharp the picture can be. A properly aligned wide bandwidth receiver shows the extra detail quite well.

Below is a photograph I took from my 8T243 about years ago. It was from an over-the-air analog broadcast directly displayed on the receiver.

I have an Apex DTV box and it too has the S-Video output. Instead of getting into the box, I thought of just separating the luma coax from an S-Video lead and attaching an RCA connector to feed a separate modulator. However, using WA2ISE's solution means that I can use the internal modulator.

Last edited by Penthode; 02-26-2025 at 09:42 PM.
Reply With Quote
  #3  
Old 03-02-2011, 01:12 AM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by Penthode View Post

I have an Apex DTV box and it too has the S-Video output. Instead of getting into the box, I thought of just separating the luma coax from an S-Video lead and attaching an RCA connector to feed a separate modulator. However, using WA2ISE's solution means that I can use the internal modulator.
Don't know how Apex does it, it may be similar to how Channel Master did it.

But if you do use an external modulator, you may be able to change the channel it uses, from the usual 3 or 4 to 2, 5 or 6 by removing the usually 4 legged crystal and installing a regular 3rd overtone crystal cut for 55.25MHz for channel 2, 77.25 for channel 5 and 83.25 for channel 6. I found that crystals for 18.432MHz will also usually work for channel 2, 25.75MHz for channel 5 and 27.75 for channel 6. Depending on how much fine tuning the set's tuner will allow, 27MHz crystals from CB radios may work well enough. This assumes such crystals will oscillate in the channel 5 frequency region.
__________________
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:56 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.