Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-11-2010, 06:56 PM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
I ran out last night to check and see if Home Depot had those adapters for the 300 ohm connections in the back of my tv. They didn't, so I waited and got one from Radio Shack today since the old one was messed up. But, to make the trip worth something while I was at Home Depot, I picked up some Howard's Restore-A-Finish in mahogany for my cabinet and a pack of fine steel wool. Today, the weather was nice so I immediately jumped at the chance to do something I've been wanting to do for a long time; fix up that scratched cabinet! It really didn't look too bad already, especially from the front where there were maybe only a dozen or so very small nicks that were somewhat noticable. The sides and top didn't fair so well. They still looked "okay" but were scratched beyond belief in some spots, especially the left side.

The Howard's stuff really did wonders for this type of damage without too much work at all. I think it took a couple hours with a bit of drying in between. I was pretty liberal with the top and sides, but very light with the front where I wanted to merely "touch up" the trouble spots. I still ended up rubbing a thin coat over the whole front end, although careful to avoid to the grille cloth.









The scratches are practically invisible and that color is just amazing! It's like I'm slowly turning the clock back 50 years. I could still touch up a few more spots and maybe wax it, but for now I'm happy with it. Now I'm just waiting on some rather expensive Krylon gold paint to get here so I can finish up the control panel. I've still got the chassis out so I'll be investigating the video output section tonight. More to come soon!
Reply With Quote
  #2  
Old 10-11-2010, 08:07 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Looks nice! I'll have to try that stuff.
Reply With Quote
  #3  
Old 10-13-2010, 10:21 PM
bandersen's Avatar
bandersen bandersen is offline
RCA 741PCS
 
Join Date: Mar 2009
Location: Chicago, IL
Posts: 8,829
Quote:
Originally Posted by RitchieMars View Post
...The scratches are practically invisible and that color is just amazing! It's like I'm slowly turning the clock back 50 years. I could still touch up a few more spots and maybe wax it, but for now I'm happy with it....
Lookin' good
I've used Howard's a few times before and really like it too. One downside though - it will fade after a while. They recommend Howard's Feed-d-Wax. It's orange oil and beeswax - great stuff
__________________
Here are my Vintage Radio & TV YouTube Channel and Photo Gallery
Reply With Quote
  #4  
Old 10-13-2010, 10:34 PM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
Yeah, I think I'll get some of that stuff to maintain the finish. I know they recommended using that on the back of the can rather than using some kind of lacquer or other finishes over it. I don't expect it to be really glossy, but I would like to keep it from becoming dull or hazy.
Reply With Quote
  #5  
Old 10-17-2010, 07:55 PM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
Well, I just got back from North Carolina today and got some things in the mail. I got my attenuator, a 12BY7, and a 6AU6. I've tested the set after installing both tubes and the attenuator but not adjustment seems to remedy any of my previous problems. The sound still distorts and buzzes pretty bad on most channels, and I have very little contrast. Back to the drawing board, I guess. I'll be pulling the chassis back out and going over the video and IF section again following some suggestions I've heard here and see what I can find.

UPDATE: By the way, that fringe lock control caused a sudden pop again last time I tried adjusting it. I'm not sure what it is. It sounded like something arched and there was a flash inside the set, but no burn smell and no change in performance. It has NEVER done it other than when I've turned the fringe lock to a certain spot. Pretty unnerving...

Last edited by RitchieMars; 10-18-2010 at 07:55 PM.
Reply With Quote
Audiokarma
  #6  
Old 10-19-2010, 01:07 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Quote:
Originally Posted by RitchieMars View Post
Well, I just got back from North Carolina today and got some things in the mail. I got my attenuator, a 12BY7, and a 6AU6. I've tested the set after installing both tubes and the attenuator but not adjustment seems to remedy any of my previous problems. The sound still distorts and buzzes pretty bad on most channels, and I have very little contrast. Back to the drawing board, I guess. I'll be pulling the chassis back out and going over the video and IF section again following some suggestions I've heard here and see what I can find.

UPDATE: By the way, that fringe lock control caused a sudden pop again last time I tried adjusting it. I'm not sure what it is. It sounded like something arched and there was a flash inside the set, but no burn smell and no change in performance. It has NEVER done it other than when I've turned the fringe lock to a certain spot. Pretty unnerving...
Did the attenuator have enough range to take the reception from "strong" down to a weak snowy picture?... and you still had buzz?

The pot problem could be related to dendritic growth... a growth of tin or lead "whiskers" from the pot body, which can short it out/contact the wiper as it moves. Humidity and electric field contribute to this crystal growth... might want to take the pot apart and check it/clean it. Since the pot can affect video and sync pulses, it might be part of the problem that you are having.
jr
Reply With Quote
  #7  
Old 10-19-2010, 01:29 PM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
This is the attenuator I was using:

http://cgi.ebay.com/Adjustable-TV-UH...item518baade82

It seems like the MIN side is mostly the same as what I have without it, and the MAX side gradually turned it to distortion and static. Referring back to your previous post about these, that sounds about right. So yes, the MAX attenuation results in a more snowy picture and finally nothing but static. The buzz was present when a picture was present, past that it's all noise.

I'll have a look at that pot when I pull the chassis out tonight. Honestly, I think it was the steel wool I used awhile back. A little shard of it must have rubbed off in there when I was doing some light polishing on a part of the chassis back there. Guess I won't be doing that anymore.

Last edited by RitchieMars; 10-19-2010 at 01:39 PM.
Reply With Quote
  #8  
Old 10-19-2010, 03:30 PM
Phil Nelson's Avatar
Phil Nelson Phil Nelson is offline
VideoKarma Member
 
Join Date: Jan 2006
Posts: 4,030
I have the same R-S attenuator and I never found much use for it.

I asked a question a while back, but I don't recall seeing an answer:

If you totally ignore the audio (turn it all the way down), is there a combination of picture controls -- brightness, contrast, etc. -- that gives you a nice picture?

If the answer is Yes, then perhaps you can focus on the audio.

Just looking for a simple way to isolate the real problem. Some times, trying to "fix everything at once" leads you down blind alleys.

Phil Nelson
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:29 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.