Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-08-2010, 03:22 PM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
2 Questions!

First, as I go about ordering the electrolytic caps, I noticed that a few of the value's I need for this set are out of stock. I can order the same value of the next available higher voltage rating, or exceed the value without having to go up and thus save a bit on price. I've read that it's safe to exceed the capacitance value in radios, so is that still fair game in a television set like this?

Also, where do I find a power cord? Simple issue; replace cord. But, I really, seriously, have no idea where to get one for my television. It's a simple brown cord, non-polarized blades, and the end that goes to the set has a plastic piece with two female ends ( like what some call a figure-8 ) and it has tabs with holes as if to use screws or rivets on either side. My cord wasn't screwed or revetted, but simply flopping around in an interlock. Don't like it.



It's stuck in there, so I guess I'll have to drill the rivets that hold the interlock together to the back cover, but I still don't know where to find a proper cord. I've tried searching for it online, but I don't know what I'm looking for? Not too keen on power cords...
Reply With Quote
  #2  
Old 09-08-2010, 08:50 PM
marty59's Avatar
marty59 marty59 is offline
VideoKarma Member
 
Join Date: May 2008
Location: Arlington, Tx
Posts: 915
If the cord is in otherwise good condition, don't be concerned about it. It should "float" in it's mounting to help facilitate the installation of the back, and the alignment of all the back's screws while at the same time confirming the mating of the cord to the chassis.

Hopefully, you should have some spare (loose) cords for troubleshooting, otherwise known in the trade as "cheater cords".

If you do need one maybe Moyers or Mock Electronics for starters will have some NOS ones. I've got quite a stash of 'em so I really haven't given it much thought as to where to purchase them anymore...
Reply With Quote
  #3  
Old 09-09-2010, 09:25 AM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
The original cord is partially cut in half. I had it patched up just to test it before, but I need a correct replacement, or at least a brown cord that's compatible. I have cords that will work crudely for testing, but I don't want to be stuck with any of those as a final solution. So, I'm just keeping my eyes out for a NOS or at least something close. I'm not picky about originality, just appearance. The old cord didn't even say "Zenith" on it. Just "Phalo, USA" whoever that was.
Reply With Quote
  #4  
Old 09-09-2010, 09:59 AM
Phil Nelson's Avatar
Phil Nelson Phil Nelson is offline
VideoKarma Member
 
Join Date: Jan 2006
Posts: 4,030
Quote:
Originally Posted by RitchieMars View Post
I've read that it's safe to exceed the capacitance value in radios, so is that still fair game in a television set like this?
Using the next higher value should not be a problem. For instance, substituting 33uf for 22 uf is OK. The higher value may be a little larger physically. I would not go more than twice the spec'd value. Check the B+ voltage after you're done recapping to make sure it's within reason. A little higher than spec'd is OK (pretty common, actually, since line voltages are somewhat higher now).

Phil Nelson
Reply With Quote
  #5  
Old 09-09-2010, 04:26 PM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
Alrighty. Well, I couldn't find a 40uF in a voltage rating I needed, so I went up to a 47uF in those cases. Oddly enough, I found a 4uF rated at 550v in my parts list, but in the schematics, the circuit legend, and in the television itself on the cans, the corresponding filter cap was actually labeled as 4uF at 350v. I guess it was a typo. It made the difference between a $1 cap versus a $4 one, so I'm glad I noticed it.
Reply With Quote
Audiokarma
  #6  
Old 09-22-2010, 04:07 AM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
I started recapping the set yesterday and I got a good bit more done today. Nothing but a couple bumblebee's and the electrolytics left. I noticed that one of these 47uF's I've got will replace a 40uF that appears to be first in line to the 5U4G low voltage rectifier. I recall hearing that exceeding the original capacitance rating of filter capacitors closest to the rectifier could overdraw the rectifier during the start-up surge. The 47uF's are all I could find, and it's only 15% off. Cause for concern? Just thought I'd get a second opinion on this.
Reply With Quote
  #7  
Old 09-22-2010, 07:26 AM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
It won't matter. You'd have to be off by a huge amount. 15% is still smaller than the normal tolerance of electrolytics.

John
Reply With Quote
  #8  
Old 09-22-2010, 03:00 PM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
Ah, well that's good. I had figured as much, but I thought I'd make sure. I've replaced about 26 capacitors so far, so I've got less than a dozen left. It's getting close to that time... about to find out if she glows or blows.

UPDATE:



Almost there... 5 more electrolytics and a couple hard-to-reach capacitors still left to go.

Last edited by RitchieMars; 09-22-2010 at 05:26 PM.
Reply With Quote
  #9  
Old 09-23-2010, 05:08 AM
RitchieMars's Avatar
RitchieMars RitchieMars is offline
VK Member
 
Join Date: Apr 2010
Location: Fountain Inn, South Carolina
Posts: 244
New problem...

I finished recapping my Zenith tonight and was ready to test it out with the new CRT, but I now have reason to suspect that the rebuilt CRT I bought awhile back isn't really a 17LP4. While it does look nearly identical to the original, I'm having problems getting it to fit in the cabinet properly. I've managed to get it inside, but it looks "different" once you get it in there. I can see the edge of the black frame that supports the CRT more than before, and it looks higher up with more of a gap at the bottom. Worse still, is the fact that the shafts of the switches don't stick out as far as before, and I can't even get my power/volume knob on far enough to keep it in place.

I don't know what to do, honestly. I've been working on this all night, and I'm exhausted. I've pulled that chassis out 3 times so far, and I still can't get it right. Guess I'll try and figure it out tomorrow...



Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:05 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.