Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 09-07-2010, 02:53 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
micro panic time...

I am cleaning up the contacts, including the CRT cathode plug in connections.

Of course I put the red gun to the wrong post. After futzing with if for 30 min I realize my error, put it back all fine now, except for my messing up all the screen drives and controls trying to get the red to work.

I checked the CRT no damage, excellent tracking and good emissons, so at least I did not hurt anything but my wits.

Oh well it needed a good setup anyway, now I have a reason to do from scratch.

still has that annoying high pitched un even noise at start up, I cant be sure where its coming from. I tried touching the fly and the yoke with a wood stick to see if I could affect it, but no joy. I wonder if it could be coming from the pin cushion? the thing is its also gets some noise into the pic (the streaks). I will keep running it and see if it improves. Its not a big deal since it always stops and does not come back after the inital warm up.
Reply With Quote
  #2  
Old 09-07-2010, 07:45 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
boy this thing is kicking my butt. The new HOT tube fixed the squeal, but then I lost HV regulation (would bloom too easy, and the HV adj did nothing. Wide open with no beam current would be about 24k, but would drop to below 20k and be moving all over the place with the beam current. I also lost width. So I tried ANOTHER 6JS6 HOT, plenty of HV now, in fact all the way down and even with a bright screen its 25-27kv, too much really. Not sure I will try a couple more HOT's if I can find (I have a few pulls to try) but I may end up having to buy one. Oh and the width problem went away. Still now squeal so that is good. I may but that squeal tube back in and see how it goes.

I tried the purity setup, the yoke did not seem to go back far enough to get the red blob in the middle, so I just fiddled with the purity tabs to get the red centered as best as I could (most of the screen was red) then pushed forward to get it to cover the whole screen in red. Color purity looks good now. still some dynamic convergence to work on.

Still have not pulled the chassis to replace those few HV film caps.
Reply With Quote
  #3  
Old 09-08-2010, 11:10 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
progress, working on HV regulation with help from CTC17 (dan).

seems I can dial in the HOT current and HV with different HOT
s but the regualation is just not happening. will be checking the reg tube voltages tomorrow. the Plan is to replace the focus resistor (at the edge of adjustment now) and hope that effects how the regulator is working.

I had noticed the color was a bit weak, found a chroma amp screen grid resistor that had driffted up about 400% so that will get replace as well. while I have it out I will check the disk decoupler cap, just in case it was leaking, thereby stressing out the screen resistor. its just a little 82k 1/4 watt.

Last edited by DaveWM; 09-08-2010 at 11:16 PM.
Reply With Quote
  #4  
Old 09-09-2010, 06:46 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
stopped by my tube guy, checked all the tubes on a 539 hickok, turned out the HV regulator tube was very weak (and yet looked brand new). I hope that helps resolved the regulation problem.

Today I replaced 3 resistors on that chroma amp tube, while checking the other tubes he thru in the syn/noise/agc tube, two color demodulators, a new audio tube (6z10), a 2 IF tubes (one shorted, the other very weak), and an RF amp tube (again very weak).

I also replaced the focus rectifier stick.

Cleaned the chassis top, inspected the ground stakes (two were cracked) and resolded.

Cleaned all the gunk around all the term strips/tube sockets, cleaned the tube socket pins (small nylon spiral brush and cleaning juice). cleaned all the tube pins (brass brush). Cleaned all the plug in sockets (hue/color, convergence, yoke) cleaned the CRT socket (sprial brush). Wiped off all the sticky goo from the wires (yoke, CRT, speaker).

inspected the bottom for any componets that may have been moved after working on the resistors, and transporting the chassis.

Cleaned up the fly back plate (dust, general nastyness) careful not to work behind it where you cant see the fine wires.

Still need to give the pots a quick shot of cleaner/lube, that is all the pots on the chassis front, and the volume pot.

the Thermistor is busted, every set I have seen has a busted thermistor. I have a CL90 but not sure if the rating is correct. Will do some checking and see.
Reply With Quote
  #5  
Old 09-09-2010, 08:05 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
looks like the CL-90 specs out at least to the cold resistance (120@25c) and since its in the B+ it should be fine current wise. I have used them on other things, but that was on the primary side of the power tranny to soften the blow to the power switch (fisher 400).

so the thermistor is in, but its getting late so I will have to wait till prob Sat to reinstall the chassis and see how it goes. wish me luck...
Reply With Quote
Audiokarma
  #6  
Old 09-10-2010, 11:22 AM
batterymaker's Avatar
batterymaker batterymaker is offline
Repro Battery Builder
 
Join Date: Jan 2008
Posts: 179
Sounds like you're almost done. So close I can taste it...
Reply With Quote
  #7  
Old 09-10-2010, 12:15 PM
ctc17 ctc17 is offline
VideoKarma Member
 
Join Date: Jul 2009
Posts: 1,615
The adjustment on the front labeled brightness limiter should really be 'bloom limiter'
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:25 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.