Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-20-2010, 09:25 PM
rca2000's Avatar
rca2000 rca2000 is offline
VideoKarma Member
 
Join Date: Mar 2003
Location: cincinnati,ohio
Posts: 2,090
Glad you are having some success with that old set!! I expected it would be better with you---than in my storage garage.

I hope the tube is good....or at least it will "wake up" for you.

I STILL don 't remember exactly where I got that tv. I THINK it was at an Estes auction--about 6 years ago or so.
Reply With Quote
  #2  
Old 06-21-2010, 10:57 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
12VP4 test

I installed the 12VP4 in the 1-108 Chassis I have working. At first I thought the CRT was completely dead, but after turning the brightness up to maximum I was able to get a raster playing with the ion-trap magnet.

I let it play for awhile. The video shot looks better than it is because of the camera. It's barely visible in dim room light.

The scan line splits into two lines as it crosses the center. It should just get wide. I need to move the focus magnet forward. I think the apparent split is because the center of the cathode is pretty used up.

There is a pin point burn right in the center of the CRT where someone must have had HV, but no horizontal or vertical sweep. Or else it's just a defect.

I could try baking the cathode at a higher voltage. Rejuvenating it with any other method is out. I don't think even the Beltron knows about this tube.

So, do I send it to Scotty or modify the set to use a 12LP4 and keep this CRT as a collectible?

John
Attached Images
File Type: jpg 12VP4_VID.jpg (77.4 KB, 39 views)
File Type: jpg 12VP4_DOT.jpg (114.2 KB, 37 views)
File Type: jpg 12VP4_TEST.jpg (83.2 KB, 51 views)
Reply With Quote
  #3  
Old 06-22-2010, 01:49 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Looking at the dot pattern, I think that I am seeing a "hollow beam" that has less current in the center... perhaps the center of the cathode is "used up" or it may be ion damaged. I have seen cathodes where the coating in the center has been totally removed by ion bombardment, down to bare nickel.
If that is the case, It will not "wake up" with the application of 8 volts to the heater, but what have you got to loose by cooking it for a few hours?
jr
Reply With Quote
  #4  
Old 06-22-2010, 11:57 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Quote:
Originally Posted by jr_tech View Post
Looking at the dot pattern, I think that I am seeing a "hollow beam" that has less current in the center... perhaps the center of the cathode is "used up" or it may be ion damaged. I have seen cathodes where the coating in the center has been totally removed by ion bombardment, down to bare nickel.
If that is the case, It will not "wake up" with the application of 8 volts to the heater, but what have you got to loose by cooking it for a few hours?
jr
That what I was thinking too, a hollow beam.

I tried a brightener. That did little. I then cooked it, but the Beltron manual suggested 10 volts so that's what I used. It made it almost watchable, but it faded after a few minutes of use.

It's in a box and will be on its way to Scotty tomorrow.

John
Reply With Quote
  #5  
Old 06-23-2010, 01:20 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Quote:
Originally Posted by jeyurkon View Post

It's in a box and will be on its way to Scotty tomorrow.

John
So Scotty will have a new cathode installed in the old gun?... or does he have a supply of the triode guns?

jr
Reply With Quote
Audiokarma
  #6  
Old 06-23-2010, 02:13 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Quote:
Originally Posted by jr_tech View Post
So Scotty will have a new cathode installed in the old gun?... or does he have a supply of the triode guns?

jr
He will have the gun rebuilt. Hopefully there's nothing else wrong with the gun like an enlarged hole at the end of the gun. I don't know what all they can rebuild.

The gun in the 12VP4 uses ceramic supports instead of glass. I wonder if this makes any difference in the difficulty of rebuilding it.

John
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:08 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.