Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 05-18-2010, 06:42 PM
Eric H's Avatar
Eric H Eric H is offline
Administrator
 
Join Date: Jun 2002
Location: So. Calif
Posts: 11,565
I seem to recall someone tried soaking one in a wading pool full of plain water once with good results, took several days but no danger of implosion.

It may not work with some types of adhesive.
Reply With Quote
  #2  
Old 05-18-2010, 07:24 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Exclamation


You may want to use a full face shield, the sort welders use. Flying glass could get past the glasses. Besides, flying glass on bare face skin won't be a picnic even if it stayed out of the eyes.
__________________
Reply With Quote
  #3  
Old 05-18-2010, 10:29 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Quote:
Originally Posted by Eric H View Post
I seem to recall someone tried soaking one in a wading pool full of plain water once with good results, took several days but no danger of implosion.

It may not work with some types of adhesive.
That makes a lot of sense since PVA was used.


Quote:
Originally Posted by wa2ise View Post
You may want to use a full face shield, the sort welders use. Flying glass could get past the glasses. Besides, flying glass on bare face skin won't be a picnic even if it stayed out of the eyes.
I second that. Where I work, full face shields over safety glasses are required when grinding. Flying glass would be worse. I'd worry about the neck area too.
Reply With Quote
  #4  
Old 05-19-2010, 07:10 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
well I have a swimming pool, I may just go set it face down in there and let it be for a week or two, just the face of course I dont want to rust the anode or pins.
Reply With Quote
  #5  
Old 05-19-2010, 08:14 AM
sampson159's Avatar
sampson159 sampson159 is offline
sampson159
 
Join Date: Sep 2007
Location: columbus,ohio
Posts: 2,170
a small wading pool is perfect.you dont have to fill it up all the way.enough water to submerge the safety glass only.i have used many methods.one effective was the use of wd 40 and a heat gun.spray it into a loose edge and watch it penetrate .use of the heat gun forces it to spread,loosening the glass.it speeds the progress tremendously.the hot wire,hammer and chisel,piano wire,etc.i think i have ran the gamut.the wading pool is the safest,but also the most time consuming!
Reply With Quote
Audiokarma
  #6  
Old 05-19-2010, 01:32 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
ok I will will do the wading pool approach and report back, no hurry since I dont need this CRT right at the moment.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:53 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.