Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 03-15-2010, 06:02 PM
Tubejunke's Avatar
Tubejunke Tubejunke is offline
VideoKarma Member
 
Join Date: Apr 2003
Location: Martinsville, VA
Posts: 1,823
OK, I finally did something with this. I removed the two tuner tubes and tested them; both are good. I always scrape the pins of tubes with my knife for good measure, especially if I see the needle on the tester jump around, and I did with one tube. Anyway, I replaced them and tried the set with and without the metal shields to see if that would make a difference. I forgot to say that cleaning the pins on the tubes must have done some good because the worst of the interference I mentioed was gone. However, the picture was still a bit snowier than I would like it to be. So, I connected ONE side of the built in VHF antenna to ONE side of the antenna terminal and MOST of the snow came out. The TV is now viewable! That's good, but I wish I could get the picture crystal clear like it used to be. Perhaps some more experimenting will work that out. Maybe there are other tubes involved.

Last edited by Tubejunke; 03-15-2010 at 06:11 PM.
Reply With Quote
  #2  
Old 03-16-2010, 02:18 AM
old_tv_nut's Avatar
old_tv_nut old_tv_nut is offline
See yourself on Color TV!
 
Join Date: Jul 2004
Location: Rancho Sahuarita
Posts: 7,815
Quote:
Originally Posted by Tubejunke View Post
However, the picture was still a bit snowier than I would like it to be. So, I connected ONE side of the built in VHF antenna to ONE side of the antenna terminal and MOST of the snow came out. The TV is now viewable!
Now, what you said sounds squirrelly to me. Could you state plainly how you have the converter hooked to the TV?
Should be:
Converter output 75 ohm coax --> balun transformer (75 coax to 300 ohm converter) --> 300 ohm twinlead (usually a short piece with spade lugs built into the 75-300 ohm balun) --> 300 ohm screw terminals of TV.

Are you saying that you hooked up the internal antenna on one side ALSO in addition to the 300 ohm twin lead from the balun? Or what, exactly?
Reply With Quote
  #3  
Old 03-16-2010, 05:29 PM
Tubejunke's Avatar
Tubejunke Tubejunke is offline
VideoKarma Member
 
Join Date: Apr 2003
Location: Martinsville, VA
Posts: 1,823
Quote:
Originally Posted by old_tv_nut View Post
Converter output 75 ohm coax --> balun transformer (75 coax to 300 ohm converter) --> 300 ohm twinlead (usually a short piece with spade lugs built into the 75-300 ohm balun) --> 300 ohm screw terminals of TV.

Are you saying that you hooked up the internal antenna on one side ALSO in addition to the 300 ohm twin lead from the balun?
Yes... however, I have never heard the matching transformers refered to as a "balun", my connections are as you stated with the addition of BOTH legs of the factory internal antenna connected to ONE side of the antenna screw terminals.
__________________
"Face piles of trials with smiles, for it riles them to believe that you perceive the web they weave, and keep on thinking free"
Reply With Quote
  #4  
Old 03-17-2010, 10:23 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Quote:
Originally Posted by Tubejunke View Post
Yes... however, I have never heard the matching transformers refered to as a "balun", my connections are as you stated with the addition of BOTH legs of the factory internal antenna connected to ONE side of the antenna screw terminals.
If that helps it sounds like there is something wrong with the balun or the coax.

John
Reply With Quote
  #5  
Old 03-18-2010, 10:52 AM
Tubejunke's Avatar
Tubejunke Tubejunke is offline
VideoKarma Member
 
Join Date: Apr 2003
Location: Martinsville, VA
Posts: 1,823
Quote:
Originally Posted by jeyurkon View Post
If that helps it sounds like there is something wrong with the balun or the coax.
Thanks John! I have tried a couple of different baluns and it makes no difference. I have not tried new coax, but the cable that I use is brand new. It came with the digital converter box. Perhaps a given cable could act differently on an old set due to an impedance issue that makes no difference on a newer set.
__________________
"Face piles of trials with smiles, for it riles them to believe that you perceive the web they weave, and keep on thinking free"
Reply With Quote
Audiokarma
  #6  
Old 03-18-2010, 11:25 AM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Quote:
Originally Posted by Tubejunke View Post
Thanks John! I have tried a couple of different baluns and it makes no difference. I have not tried new coax, but the cable that I use is brand new. It came with the digital converter box. Perhaps a given cable could act differently on an old set due to an impedance issue that makes no difference on a newer set.
If you're anything like me, I sometimes bend over the center conductor without realizing it. You can still easily screw the connections together, but it ends up shorted nor not connected. I've done this too many times.

John
Reply With Quote
  #7  
Old 03-19-2010, 03:14 PM
Tubejunke's Avatar
Tubejunke Tubejunke is offline
VideoKarma Member
 
Join Date: Apr 2003
Location: Martinsville, VA
Posts: 1,823
Quote:
Originally Posted by jeyurkon View Post
If you're anything like me, I sometimes bend over the center conductor without realizing it. You can still easily screw the connections together, but it ends up shorted nor not connected. I've done this too many times.
Yes, but remember that I have achieved a pretty good picture with most of the interference that started this thread gone. I simply added that the picture had what I would call 'snow' in it still, so just as an experiment I touched the set's internal VHF antenna to ONE of the terminal screws a wa-la, the picture got a lot better. Even so, the picture still has a little bit of snow in it and I know that the set can display a crystal clear picture, short of HD that is... LOL! So there is no way that I could have bent the coax center conductor because I have a picture and sound where there would be none if it were open or shorted. Thanks for watching out for me though......
__________________
"Face piles of trials with smiles, for it riles them to believe that you perceive the web they weave, and keep on thinking free"
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:15 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.