Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 12-01-2009, 07:49 PM
wa2ise's Avatar
wa2ise wa2ise is offline
VideoKarma Member
 
Join Date: Dec 2002
Location: USA
Posts: 3,147
Quote:
Originally Posted by DaveWM View Post

If someone can explain how the interlace is controlled pls jump in.
Vertical sync has twice horiz frequency serrations, and sync separators are essentially low pass filters. In one field of video, the vert sync starts at a regular timed horiz sync pulse, the other field it starts at a halfway point between regular timed horiz sync pulses. The object is to try to avoid the horizontal sync from contaminating the vertical sync pulses and vertical oscillator circuits. If that happens, the interlace gets "line paired" and you lose vertical resolution. Scan lines on top of each other instead of halfway in between. But keeping the horizontal sync pulse out of everything else in the TV set is easier said than done, it gets into most everything. Maybe if the vert circuits use horiz B+ boost, a filter cap is not filtering well enough?
__________________
Reply With Quote
  #2  
Old 12-02-2009, 12:59 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
I tried to attache the schematic, it was too big. I will try again later, hope you can point out a possible problem area.
Reply With Quote
  #3  
Old 12-02-2009, 01:18 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
there is a .047 cap coming off the screeen of the HOT to ground, perhaps some kind of decoupler? I do not recall checking that one. It looks like a decoupling network as after the cap there is a 8200 5w resistor then it goes to the 245v B+, the Screen of the vert output is connected directly to the 245v source.

I am guessing the .047 cap will work as a decoupler at the freq of the HOT.

If the cap was bad it would have to be open (if it was leaky I would have a drag on the B+) I will try just jumping another cap and see if it has any effect. It's one of those brown dipped one, and I already had a couple bad one of those (leaky, .22uf 200v). The 400v ones tested ok, but I did not test that one.

all the filter can caps and doublers were replaced. as well as the electrolytic cathode bypass caps .
Reply With Quote
  #4  
Old 12-03-2009, 09:39 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
no change after jumping a new cap on that HOT screen.

think it is time to break out the scope and snoop around. I will check the wave pattern on a good set (same chassis) vs this one, on the grid of the vert output tube. then I will adj the vert hold so I get the over lap, that way I hope I can see what the pattern looks like, and if I can see the diff.

one thing I was checking was the voltages of the vert out, 0 on grid, 22 on cathode, all 3 of these chassis have this result, yet the sams say should be
-2.7 and 15. I have checked both the coupling cap and grid leak resistor, both ok. I tried different tubes, including some NOS (thinking it may have been gassy), I get some different cathode voltages (20-23) but the grid is always 0. I check with a DMM and a VTVM with and with out video signal.

The DMM would show millivolts some neg but very small like -50mv and it would jump around.
Reply With Quote
  #5  
Old 12-06-2009, 09:46 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
Quote:
Originally Posted by wa2ise View Post
Vertical sync has twice horiz frequency serrations, and sync separators are essentially low pass filters. In one field of video, the vert sync starts at a regular timed horiz sync pulse, the other field it starts at a halfway point between regular timed horiz sync pulses. The object is to try to avoid the horizontal sync from contaminating the vertical sync pulses and vertical oscillator circuits. If that happens, the interlace gets "line paired" and you lose vertical resolution. Scan lines on top of each other instead of halfway in between. But keeping the horizontal sync pulse out of everything else in the TV set is easier said than done, it gets into most everything. Maybe if the vert circuits use horiz B+ boost, a filter cap is not filtering well enough?
gonna try jumping in a cap on the various filter caps to see if that has any effect.
Reply With Quote
Audiokarma
  #6  
Old 12-08-2009, 11:12 AM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
Quote:
Originally Posted by wa2ise View Post
Vertical sync has twice horiz frequency serrations, and sync separators are essentially low pass filters. In one field of video, the vert sync starts at a regular timed horiz sync pulse, the other field it starts at a halfway point between regular timed horiz sync pulses. The object is to try to avoid the horizontal sync from contaminating the vertical sync pulses and vertical oscillator circuits. If that happens, the interlace gets "line paired" and you lose vertical resolution. Scan lines on top of each other instead of halfway in between. But keeping the horizontal sync pulse out of everything else in the TV set is easier said than done, it gets into most everything. Maybe if the vert circuits use horiz B+ boost, a filter cap is not filtering well enough?
after re-reading what you said, I am going to see if I can figure out the network that comprizes the low pass filter. I think I get it now (did some reading on trouble shooting with a o scope, esp vert sweep and sync circuits).
Reply With Quote
  #7  
Old 12-08-2009, 09:54 PM
DaveWM DaveWM is offline
VideoKarma Member
 
Join Date: Feb 2009
Location: Orlando FL
Posts: 5,607
on what I belive was the low pass filter (a resistor cap to ground cap to grid of osc) from the sync separater/phase inverter I found a cap that was a .01 and per the schematic it was suppose to be a .002 (verified that on two other sets with the same chassis). It did not look original. I replaced it, still have the interlace instability (it jumps in and out). I put a scope on it and checked the input to the vert osc one check has it with the osc tube in and the other with it out (brt turned down). in both cases the wave seemed to move around on the scope, not so on the other set that is good. with the tube pulled you can see the sync pulse, on the good set it looks like the sams on the bad set the low part of the wave it thick, if I speed up the scan I can clearly see a hi freq wave in it. both sets have this, but on the bad set it in prob 4 times as big. I will post some pic later to try and make it clear what I am saying. the other scope readings of the sync sep and agc keying tubes were in conclusive, did not look anything like the sams, but neither did the working set. I will have to go back and take better notes, one ready I got was about a 3 order magnitude higher on the non working set than the working set.

checked it:
that was on the sync phase inverter grid, the non working set was much higher amplitude than the working set.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:06 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.