Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 10-28-2009, 01:11 AM
Phil Nelson's Avatar
Phil Nelson Phil Nelson is offline
VideoKarma Member
 
Join Date: Jan 2006
Posts: 4,030
Thanks, lots of good stuff to think about.

If I'm reading the article correctly, it says my single-magnet iron trap is in the right spot, "well behind the flags."

With that and the focus coil both adjusted, the focus control works within the middle of its range. You can adjust so the picture is sharp, then too sharp & grainy, and if you keep going, it will eventually blur again. Which seems normal to me.

Re the trailing, a little while ago I switched from the DVD player to rabbit ears (receiving signal from my agile modulator across the house). Maybe that player just overloads this AGC-less set. With rabbit ears, I can see a tiny amount of trailing if I look hard, but I doubt anyone else would notice it. The picture seems generally better & easier to adjust in other ways, too. Riders doesn't have any adjustment info for DC restoration.

Re the width, I checked voltages on the 6BG6 tube. Pins 3 and 5 are right on the money. Pin 8 is a little low, 224v rather than 250v. I checked the resistance of the parallel 2W resistors (R247/R301) in place, getting 14.3K (would the ideal would be 12-something K ?). I don't have any 2W resistors in the house, but it will be easy enough to order replacements and see what happens if I replace those two.

Wish I could post a photo showing the improved picture, but my danged auto-everything camera can't focus the TV image well enough to show the difference. Maybe the bulbed face of the CRT is tricking it.

Anyhow, thx for all of the good advice.

Phil
Reply With Quote
  #2  
Old 10-28-2009, 08:09 AM
old_coot88 old_coot88 is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 2,654
Looks like the ol' gal is shaping up nicely, Phil. Re. the paralleled G2 resistors, they are OK, and if anything, have gone a bit high in value. That's the direction you'd want to go for reducing sweep. oc
Reply With Quote
  #3  
Old 10-29-2009, 12:22 AM
Phil Nelson's Avatar
Phil Nelson Phil Nelson is offline
VideoKarma Member
 
Join Date: Jan 2006
Posts: 4,030
Looking back at a couple of these photos, now I am wondering whether this CRT was rebuilt.

The sticker on the CRT bell is hand-lettered 12JP4, which made me think "rebuild." But the stamped name looks like it could be Hytron. Would a rebuilding shop use a factory sticker? Or something more like "Joe's Rebuilt Picture Tubes?"

The picture of the gun inside the neck doesn't show any welds or seams in the glass. When you rebuild a tube, wouldn't you leave some kind of visible seam in that area?

It's a very strong tube either way. Just curious.

Phil
Reply With Quote
  #4  
Old 10-29-2009, 02:31 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Quote:
Originally Posted by Phil Nelson View Post
Looking back at a couple of these photos, now I am wondering whether this CRT was rebuilt.

The sticker on the CRT bell is hand-lettered 12JP4, which made me think "rebuild." But the stamped name looks like it could be Hytron. Would a rebuilding shop use a factory sticker? Or something more like "Joe's Rebuilt Picture Tubes?"

The picture of the gun inside the neck doesn't show any welds or seams in the glass. When you rebuild a tube, wouldn't you leave some kind of visible seam in that area?

It's a very strong tube either way. Just curious.

Phil
But the gun does not appear to be a 12JP4...remember a 12JP4 does NOT require an ion trap, your gun appears to be a tilted offset/ slashed field type which requires a single ring magnet. Why would the factory put the wrong gun in a tube? I suspect that rebuilders often made substitutions when the proper gun was unavailable.

The re-neck seal could possibly be hiding under the yoke or focus coil.

Also, the first letter of the logo on the label does not look like an "H", but instead has a closed top... so I don't think it is "HyTron" but perhaps something designed to look similar.

jr

Last edited by jr_tech; 10-29-2009 at 03:16 PM.
Reply With Quote
  #5  
Old 10-29-2009, 07:07 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Quote:
Originally Posted by jr_tech View Post
But the gun does not appear to be a 12JP4...remember a 12JP4 does NOT require an ion trap, your gun appears to be a tilted offset/ slashed field type which requires a single ring magnet. Why would the factory put the wrong gun in a tube? I suspect that rebuilders often made substitutions when the proper gun was unavailable.

The re-neck seal could possibly be hiding under the yoke or focus coil.

Also, the first letter of the logo on the label does not look like an "H", but instead has a closed top... so I don't think it is "HyTron" but perhaps something designed to look similar.

jr
Any idea of which type it could be? I think this is a diagram of the tilted offset/slashed field that you're describing. It's from the 1969 RCA tube design book.

John
Attached Files
File Type: pdf Pages from RCA_1962_Electron_Tube_Design.pdf (76.4 KB, 14 views)
Reply With Quote
Audiokarma
  #6  
Old 10-29-2009, 07:24 PM
jr_tech's Avatar
jr_tech jr_tech is offline
VideoKarma Member
 
Join Date: Sep 2009
Posts: 4,573
Perhaps 12QP4, RP4, UP4, ZP4 ...? I don't know,but all of these 12" types are shown in my old (don't see a date...early 60s?) GE tube manual, as requiring only a single magnet.

jr
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:03 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.