Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Early B&W and Projection TV

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 04-29-2009, 07:54 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
While doing some fine tuning of the set I realized that the Zenith Wavemagnet I picked up has the right inductance to use as a loop for the AM section of this set. I tried it without doing any alignment and the reception was amazing.

This might be pretty good for AM DXing.

John
Reply With Quote
  #2  
Old 04-29-2009, 08:38 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Question Volume Control Problem

I need some advice on dealing with a problem with the volume control on this set. It's a 1 meg composition pot tapped at 500K and 250K. It has a hollow shaft. The Photofact doesn't list any replacements other than Sylvania so it's pretty much going to be impossible to find.

The resistance from one end to the other is 1.2 Meg, which isn't so bad. The Symptom is that the volume jumps up to a loud leve when I start turning it up.

I've attached a scan of this section.

It seems that a spot was burned in the conductive film near the bottom of the pot. Possibly when paper cap C25 was leaky. As you go past this spot the resistance measured at the wiper jumps from 25 ohms to 250 ohms. If I measure the resistance to ground from the other taps they jump down to the correct value when the wiper is in the center of this spot. I imagine the conductive trace having a burned spot in the center of the trace, but good on both sides. I've attached a sketch of what I think it might look like.

I think the taps are there to keep the tone the same as the volume is changed. I could just short the 250K tap to ground. I'd lose a portion of the range. The tone might sound a little different. This would be the easiest solution.

I could try coating the spot with aquadag to cover the burned spot. If it's small enough, it might not be noticiable.

To get at it I have to remove the CRT, the front panel, and the plate that holds the pulley for the dial cord. I hope to avoid that.

Any other suggestions on how to attack this problem?

John
Attached Images
File Type: jpg trace_control.JPG (22.1 KB, 24 views)

Last edited by jeyurkon; 11-14-2009 at 08:11 PM.
Reply With Quote
  #3  
Old 04-30-2009, 03:45 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Well, the problem with the volume control wasn't what I thought it was, and the problem was fixed by an unfortunate accident.

Instead of a burned spot on the resistive trace, it was where the terminal on the ground side was riveted to the phenolic board with the resistive trace. I didn't notice that a tubular capacitor that is on the end of a coax running to the wiper of the volume control was too close to a resistor. It arced through the paint on the capacitor while I was watching and made violent discharges in the volume control. I expected the worst. But, it turns out it just improved the connection so now the volume control tests and works perfectly!

John
Reply With Quote
  #4  
Old 05-17-2009, 01:12 AM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
While I was able to adjust the set to give a good picture, there was still a problem with the horizontal. I wasn't able to adjust it according to the service literature. Basically you're supposed to remove the discriminator tube, the 6AL5, adjust the frequency until the bar moves slowly across the screen and reinsert the tube. It should lock in at this point and then you adjust the phase.

They then have test the pull-in range by adjusting the frequency CCW until it unlocks, then adjust it back slowly until it locks in and you count the number of bars just before it locks in. Then CW and count the bars. They're supposed to be between 3-4 bars in both cases. In my case when I turned it one way it would just slowly drift across. In the other direction it wouldn't unlock until I made many turns.

I also wasn't able to adjust the phase independently.

I checked all the caps and resistors. I replaced the micas. Nothing helped. I started to suspect the horizontal oscillator transformer. But, I noticed that the DC level on the grid of the 6AU6 control tube was -1V when it should have been -3V. The 6AU6 is used as a reactance tube to control the frequency based on the output of the phase discriminator. -1V put it at one end of it's control range so it could only adjust the frequency in one direction if the free running frequency was set correctly.

The bias is determined by dividing down the -125V supply. First they divide it down to -30V with a low impedance divider then down to -3 with a 10meg and 1meg in series. I checked those and they were o.k. I was getting close to modifying it to give the right bias when I decided to swap the 6AU6 even though it tested as new and seemed to work. Well the bias went to -3V with the new tube and I was able to align the horizontal sweep as per the service manual. The grid on the 6AU6 was drawing 0.2 microamps at -1volt. My tube tester isn't going to notice that.

Now the only problem I have is with the FM. Although it worked great in the beginning, it is now fading out after 4 minutes. It runs for 4 minutes after turning on and then suddenly the volume drops.

I've replaced two micamold caps. One was leaky, the other was o.k. Some resistors are out of spec, but I don't think they're at fault.

What is curious is that the AM function works fine even when the FM has dropped in volume. They both use the same circuitry except different IF transformers and osc frequency. There must be a clue in this.

You can see the schematic for the radio section on the last page of:

https://www.msu.edu/~yurkon/Sylvania_9-2_Sup1.pdf

This is getting to be really frustrating. I swapped all the tubes in the radio after my experience with the horizontal 6AU6 but it didn't make a difference. Any suggestions for what to look for would be welcome.

I'd like to get it off my bench so I can work on my alignment generator and get it working. I want to touch up the alignment since I had to rewind one of the video IF transformers.

I'm also working on making a bezel for the 12" version of this set. A friend drew a mold up for me based on my measurements. I didn't notice however that the had made the face a cylinder instead of a sphere. It wasn't obvious in the preview. It became obvious when the shop I'm using tested their programming on a shape board.

If I'm able to cast a 12" bezel then I'll put a 12LP4 into the chassis. It should really be a 12VP4 but I'm unlikely to find one of those. I'll have to add a screen bias supply. One of the 16" Sylvania shows a circuit to do that, based on this power supply.

This is basically changing it from a 1-076 model to a 1-128 model. I have the cabinet from my family's 1-128, just nothing is left of the electronics. The 1-108 chassis was used in both. If I can't successfully cast a bezel I'll refinish the 1-076 cabinet and stick with it.

John
Reply With Quote
  #5  
Old 05-17-2009, 06:58 AM
Bill Cahill's Avatar
Bill Cahill Bill Cahill is offline
Super Moderator
 
Join Date: Mar 2005
Location: St. Petersburg, Fl.
Posts: 1,298
Post

Have you re-capped the entire set?
Bill Cahill
__________________
"Tubes are those little glass things that light up orange unless there is a short.. Then they light up all pretty colors..."
Please join my forum.
http://www.tuberadioforum.com/
Reply With Quote
Audiokarma
  #6  
Old 05-17-2009, 11:41 AM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Quote:
Originally Posted by Bill Cahill View Post
Have you re-capped the entire set?
Bill Cahill
Bascially. Any that I didn't change were tested. All paper capacitors were replaced. I didn't change any ugly looking ceramics based on feedback from the forum and the fact that a sample of them that I did test, tested good.

The radio section is comletely independant except for the 6AU6 1st AF and 6Y6 power amp which is shared by the TV. The problem only occurs with the FM. The TV and AM audio are fine.

There was only one electrolytic in the radio section and I changed that in the beginning since it was shorted. I changed the two micamolds that were in the radio. There are other micas that aren't micamolds. I'm hoping it's not one of these micas because I'd have to remove most of the other components just to get at them.

Also, I've checked the HV to the radio and it doesn't change. There should be 215V on the plates but it's 238V. I've tried lowering it by running the set on a lower voltage with a variac, but this doesn't change the fading.

John
Reply With Quote
  #7  
Old 05-18-2009, 09:52 PM
jeyurkon's Avatar
jeyurkon jeyurkon is offline
VideoKarma Member
 
Join Date: Oct 2008
Location: Central Michigan
Posts: 1,699
Found the FM fading problem. Had to resort to using component cooler. It's the 2nd 10.7MHZ IF. It looks exactly like the Ktrans that Robert Casey repaired. I suspect it's the same problem.

Anyone have a 122-0011 Sylvania IF or Merit FM-254 you're willing to part with?

John
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:46 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.