![]() |
|
|
|
#1
|
||||
|
||||
|
Very Kool tv looking forward to seeing the pics. of it finished.
Good Luck Damen |
|
#2
|
||||
|
||||
|
Some progress
I'm still making slow progress. Many of the paper caps are difficult to get to, buried under other parts. I found one good paper cap so far. It was the only one that didn't have blisters on the outside. I wonder if that's related.
I've also found quite a few open or out of tolerance resistors in the audio output section. I started to do a quick check by checking the tube chart resistances given by the SAM's. I quickly learned that this was a waste of time. Many of the resistances given are wrong. The schematic from the same SAM's folder seems to agree with what I measure. It'll be easer just to check the individual resistors and not worry about whether the SAM's got it right. John |
|
#3
|
||||
|
||||
|
Chassis Photos
I've replaced all the paper caps and some of the electrolytics. I'm sure I'll get some flak for it but I kept the electrolytics that had better ESR than the replacements and had leakage in the acceptable range.
I cleaned the chassis. It's not as new looking as many of you guys are capable of producing, but if you look at the photos in the early thread, it's an improvement. The dark area around the electrolytics on top is wax that had dripped from the horizontal output choke on the bridge. If I end up rebuilding those electrolytics I'll clean it up then. I may paint the top of the power transformer, but I'm waiting until I see if I have to apply a hum fix to the transformer. They have you remove the top instead of removing the entire transformer to work on it. The thing that took the longest was restringing the dial cord for the radio section. It has three idler wheels, drive pulley and capacitor pulley. Only the capacitor pulley is accessible, you have to use hooks to deal with the others all the while maintaining enough tension to keep the cord from falling off. I hope I never have to do that again. Now I have to work on the bridge which has just as many paper caps. John Last edited by jeyurkon; 11-14-2009 at 07:59 PM. |
|
#4
|
||||
|
||||
|
Coffee Can HV
I was hoping to finish up the set tonight. That was too optimistic. There was way too much wrong with the HV section and I need to get some parts.
Originally I claimed there was almost no work done on this set. That was clearly wrong. As I dug into it I found a mixture of high quality repairs and some pretty ham fisted stuff. The ceramic disc I showed in another thread actually tested good. I replaced it anyhow. The bumble bees were all toast. A 100 ohm wire-wound was open. A 56K 2 Watt reads 100K. The factory manual shows it as 56K, the markings are for 56K, but the Sam's shows it as 5.6K. I bet that might have confused a few people. I cleaned up the oil that leaked from the 10KV 0.005uF cap. I removed the HV section from the bridge to make it easier to work on and minimize physical risk to the HV transformer. There was an incredible cold solder joint on the lead that goes to the feedback winding on the HV transformer. It was just flopping around in the solder around it. I don't know how they managed that because the lead was well tinned. They had a ball of solder about the size of a pea. I'll post some more photos once I finish the HV and before I install it back into the bridge. John |
|
#5
|
||||
|
||||
|
RF HV and Bridge recap photos
I've finished recapping the Coffee Can HV and the bridge. Now I just need to reassemble everything and hope for the best.
The first photo is the back of the RF HV module. The long white capacitor is a 10KV 0.0005uF film cap. The second photo shows the back of the bridge with the coffee can HV mounted back on to it. On the top between the yellow film capacitor and the black electrolytic there is what looks like a paper cap. That actually is a polystyrene capacitor and has unmeasurable leakage. I decided to leave it in since it didn't seem to be following the fate of the paper caps. John Last edited by jeyurkon; 11-14-2009 at 08:01 PM. |
| Audiokarma |
|
#6
|
||||
|
||||
|
Bad Horizontal Center pot
I was hoping to power the set up tomorrow. That won't happen now. While cleaning the controls I discovered that the Horizontal Center pot was bad. I opened it up hoping to repair it but it's beyond repair. It's a 140 ohm 2W wire-wound panel mount. 43-140CT by clarostat. The wire was blown in numerous spots. It must have seen a very high current to do that.
I think the closest I'm going to find is a 150 ohm 2 watt composition pot that I found at Newark. I'm going to go ahead and order that. If anyone should have something more appropriate they'd be willing to part with please let me know. John |
|
#7
|
||||
|
||||
|
What about the selenium rectifiers?
They need replacing as well... Bill Cahill
__________________
"Tubes are those little glass things that light up orange unless there is a short.. Then they light up all pretty colors..." Please join my forum. http://www.tuberadioforum.com/ |
![]() |
| Thread Tools | |
| Display Modes | |
|
|