Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 01-26-2009, 10:39 PM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Those diodes are probably good. If you are using a digital meter, check them on the diode scale. The likely problem is the chopper transistor (mounted on a heatsink) in the power supply. This transistor likely took out the control IC. In addition, replace the electrolytics in the switching circuit. 39uf, 2.2uf, 15uf, and 470uf. They are all located right there around the IC and transistor. And, check the horizontal output transistor for shorts. It's on a big heatsink close to the flyback transformer.

BTW, don't use NTE, ECG, or any Chinese knock-off parts in this application because they likely will not hold up. Use original RCA parts if possible. www.tritronicsinc.com should have the parts.

IMHO, the CTC169 was the best Thomson era RCA chassis made.
Reply With Quote
  #2  
Old 01-26-2009, 11:22 PM
Brian1234 Brian1234 is offline
AK Member
 
Join Date: Sep 2005
Location: Detroit area
Posts: 13
I had also flipped over to the diode scale while I had them hooked up (no beep in the forward direction). How could they be good if I measured 10Mohms when it should be (near) 0? Either way they're useless now, I clipped the leads then unsoldered the ends. (heh)

The horizontal output transistor is on the big heat sink in the middle of the board... looks a lot like the chopper transistor?
Reply With Quote
  #3  
Old 01-27-2009, 12:15 AM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Quote:
Originally Posted by Brian1234 View Post
I had also flipped over to the diode scale while I had them hooked up (no beep in the forward direction). How could they be good if I measured 10Mohms when it should be (near) 0? Either way they're useless now, I clipped the leads then unsoldered the ends. (heh)

The horizontal output transistor is on the big heat sink in the middle of the board... looks a lot like the chopper transistor?
Yep, it's in the center of the board and looks like the chopper transistor. If you check it in circuit, it will show a short between the two end terminals. This is normal. If you measure a short between either one of the end terminals and the center terminal, you have a shorted HOT. If the HOT is shorted, look for a swollen rectangular cap (usually blue) close to the HOT. Maybe you'll get lucky and it will just be the power supply components. And, don't worry about the rectifier diodes. 1N4007's are cheap. I usually order them by the 100.
Reply With Quote
  #4  
Old 01-28-2009, 01:14 AM
Brian1234 Brian1234 is offline
AK Member
 
Join Date: Sep 2005
Location: Detroit area
Posts: 13
Quote:
Originally Posted by radiotvnut View Post
If you measure a short between either one of the end terminals and the center terminal, you have a shorted HOT.
I didn't get a chance to do anything on it today but if you have a test like that for the chopper transistor section, let me know so I can do it at the same time.

Thanks a ton
Reply With Quote
  #5  
Old 01-28-2009, 01:37 AM
radiotvnut's Avatar
radiotvnut radiotvnut is offline
VideoKarma Member
 
Join Date: Jul 2007
Location: Meridian, MS
Posts: 6,025
Quote:
Originally Posted by Brian1234 View Post
I didn't get a chance to do anything on it today but if you have a test like that for the chopper transistor section, let me know so I can do it at the same time.

Thanks a ton
Generally when that chopper shorts, you will read almost zero ohms (a dead short) on all three terminals. If it's shorted, go ahead and change the controller IC and the caps.
Reply With Quote
Audiokarma
  #6  
Old 01-31-2009, 10:53 PM
Brian1234 Brian1234 is offline
AK Member
 
Join Date: Sep 2005
Location: Detroit area
Posts: 13
Quote:
Originally Posted by radiotvnut View Post
Generally when that chopper shorts, you will read almost zero ohms (a dead short) on all three terminals. If it's shorted, go ahead and change the controller IC and the caps.
Yup, that looks like the trouble. The HOT seemed OK, just showing a short across the outside terminals.

andy: Ah, indeed they showed about .5v when tested in diode mode... I had thought that would be enough to overcome the forward voltage drop.

tmwalsh: That acme link seems outdated. What does SMPS stand for? Thanks to the link for the exe file!
Reply With Quote
  #7  
Old 01-28-2009, 11:47 AM
andy andy is offline
VideoKarma Member
 
Join Date: Jul 2002
Posts: 4,004
000

Last edited by andy; 12-07-2021 at 05:30 PM.
Reply With Quote
  #8  
Old 01-28-2009, 10:38 PM
MRX37 MRX37 is offline
VideoKarma Member
 
Join Date: Aug 2005
Posts: 1,579
Quote:
Originally Posted by radiotvnut View Post

IMHO, the CTC169 was the best Thomson era RCA chassis made.
Um, my CTC158B chassis is pretty damn good. The only thing to really fail on it so far was the degaussing thermistor.
Reply With Quote
  #9  
Old 03-09-2009, 12:02 PM
Jeffhs's Avatar
Jeffhs Jeffhs is offline
<----Zenith C845
 
Join Date: Feb 2003
Location: Fairport Harbor, Ohio (near Lake Erie)
Posts: 4,035
Quote:
Originally Posted by radiotvnut View Post
Those diodes are probably good. If you are using a digital meter, check them on the diode scale. The likely problem is the chopper transistor (mounted on a heatsink) in the power supply. This transistor likely took out the control IC. In addition, replace the electrolytics in the switching circuit. 39uf, 2.2uf, 15uf, and 470uf. They are all located right there around the IC and transistor. And, check the horizontal output transistor for shorts. It's on a big heatsink close to the flyback transformer.

BTW, don't use NTE, ECG, or any Chinese knock-off parts in this application because they likely will not hold up. Use original RCA parts if possible. www.tritronicsinc.com should have the parts.

IMHO, the CTC169 was the best Thomson era RCA chassis made.
The CTC185xx series isn't half bad either. Once the grounds around the tuner (a major problem with this series, and all CTC-17x-18x series chassis until the CTC203, because of the onboard tuner) are soldered properly, this chassis will run trouble-free for years. Mine has nine years on it and still works as well as when it was new; I had the grounds all resoldered about eight years ago, the last time I had the set serviced. Not a bit of trouble with it since then, and a beautiful picture with the original CRT.
__________________
Jeff, WB8NHV

Collecting, restoring and enjoying vintage Zenith radios since 2002

Zenith. Gone, but not forgotten.
Reply With Quote
  #10  
Old 03-12-2009, 11:43 PM
Brian1234 Brian1234 is offline
AK Member
 
Join Date: Sep 2005
Location: Detroit area
Posts: 13
Here's what I have now, as found at mcmelectronics.com:

Transistor: 200165 $17.13 (SGSIF461 $9.29)
IC: 200419 $13.67 (TEA2261 $5.09)
47uf @ 50v: 31-5825 $1.60
2.2uf @ 100v: 31-7515 $0.61
15uf @ 50v: 31-5800 $1.26
470uf @ 35v: 31-5705 $2.08
1N4007: 1N4007F $0.40 Package: DO-41 (price for 10)

I'm tending toward the RCA transistor and the TEA IC. Good choice?
Do those look like proper caps? (especially voltages? all polarized?)
Did I pick the wrong diodes (DO-41 is glass?)

I have no specs on the thermistor, pointers please.
I stopped in at a TV shop and he said he replaces the zener too... would that be CR122 @ 3V? What wattage?

Sorry to be such a pain... unfortunately the only local parts shop left is all NTE so I'm left to pick from online store descriptions... I find them confusing. Just one example: the MCM page for the 200165 has a photo of the SGSIF461.

THANKS!
Reply With Quote
Audiokarma
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:06 PM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.