Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
  #11  
Old 10-25-2008, 08:57 PM
JesusJones JesusJones is offline
AK Member
 
Join Date: Dec 2007
Posts: 187
Use the link at the bottom to veiw this properly.


I have no comments one way or another with respect to this device. Please contact the author for further information.

(From: Mario Di Stefano ([email protected]).)

Here is the 'gadget' I use to rejuvenate 'tired' CRT's:

T1
o---+--------+ +------------------------------->
| )||(
M | )||(
A | )||( 6.3 or 12 Vac To Filament
I | )||( Secondary CRT Tube
N | )||( (no Polarity)
S | )||(
| )||(
o---|-----+--+ +------------------------------->
| |
| ----------------------------------------> CRT Cathode
|
| +-----+ _|_
-------------------| LP1 |-----o o------------> CRT 1st Grid
+-----+ P1


Where:

* T1 is a standard mains AC transformer.
* LP1 is a standard FILAMENT LAMP (60 - 100 W) working voltage according to mains.
* P1 Hand Pushbutton.

Other things needed (not shown):

* Mains switch (best if with overload protection or with fuse)
* 4 ISOLATED clips like the ones used in electronics to make contacts with the pins of ICs. These isolated clips ARE IMPORTANT. You don't have to touch any connection during the cleaning.

I think this circuit works better if the mains voltage is 220 Vac.

How to use it:

First we have an tired CRT (BW or colour is the same). We have poor image contrast, 'strange' brightness, also strange colours. Next we have to remove (if present) the CRT socket to its circuitry (beware to disconnect mains voltage FIRST!!!!!). At this point could be useful to discharge the HV using an isolated wire FIRST connected to CRT grey body and then to the make the contact UNDER the suction gummy which carries EHT. to the tube. It is not a dangerous voltage, but could be better not to discharge it over the body!

Now we have to identify the filament pins. Usually on the schematic circuitry of the Monitor/TV it is clearly written. If the schematic is not available, using an ohmmeter we should find the two contacts which gives a few ohms. These contacts usually are put aside each other) have to be connected to the transformer secondary of the circuit above. The Cathode and 1st grids can be found looking very closely into the tube glass (use lens and good light if necessary). Keep in mind the way the CRT electron sources are built. These usually follows this:

Cathode
| (B/W CRT tube)
V
O------+ | |
+ | | <- 1st Grid
Filament + | |
+ |**| <-Spark (read text below)
O------+ | |
| |
| |
Cathode O---------+ |
Connection |
|
1st Grid O------------+ (Damn'd ASCII graphics!)
Connection


Try to connect and turn on the transformer. The Filament in the CRT should turn on in a not-so-bright red (if it is a colour tube, we have 3 filaments on).

Now turn off the transformer again. Connect the Cathode wire to the cathode pin of the CRT Tube. Connect the 1st grid accordingly.

Turn on the transformer. FIRE button P1. If there is dust (due to aging) between the cathode and 1st grid, the circuit will blow-up it. If this happens, you could (but not always) even see the LP1 turn on and off randomly (a good cleaning gives a lamp OFF) and some sparks inside the tube. The tube collar glass now becomes hot: it is normal. You can even 'force' better sparks if you 'ting' your finger against the CRT glass (not so strong, of course). If it is a Colour CRT, you have 3 Cathodes, 3 1st grids a anyway 1 filament. Useless to say that the procedure have to be carried out for all these electrodes. A good cleaning, gives a LP1 steady OFF. If it is a steady bright or dim, means that a 'bridge' has been formed between the electrodes and there is no way to recover the tube. Turn off the mains, remove the connections, and re-apply the original socket. That's all. I'm not tired to say: BEWARE OF THE MAINS VOLTAGE: IT CAN KILL!! If you are not so skilled, don't try to do this procedure. I used this circuit lots of times. It worked almost anyway. I recovered lot of thrown away PC monitors, and now are working well....


Borrowed from http://www.repairfaq.org/sam/crtfaq.htm#crtwir



It pretty much uses a light bulb connected to the mains to BLAST dust off from the cathode and first grid.
I don't much see the need for the heaters to be on but apparently that's how he does it



Worth a shot?
Reply With Quote
 


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:22 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.