Videokarma.org

Go Back   Videokarma.org TV - Video - Vintage Television & Radio Forums > Rectangular Screen Tube Televisions

Notices

We appreciate your help

in keeping this site going.
Reply
 
Thread Tools Display Modes
  #1  
Old 06-23-2008, 06:25 PM
drh4683's Avatar
drh4683 drh4683 is offline
VideoKarma Member
 
Join Date: Jan 2003
Location: Chicago, IL
Posts: 2,094
Well,

I can now "salute" the general. Its fixed now. Loss of brightness control in this case was caused by R189 27K 2W carbon resistor went down in value to 8K ohms. R189 tied to the low side of all three G1 controls to ground. Keep this one in mind as there might be 3 or so of these sets in existance that might need the repair.

Brian, thanks for your help and offerings. Thanks for mentioning tekfax. I completely forgot I had those! This set has the C-2 chassis, and I found the schematic in tekfax 112. Brightness now is controlable and can get the picture very dark to near total cut off upto a nice bright picture. I tacked in a crappy short lead 27K just to see if it did the trick as its the only one I could find. I need to stop at frys and pick up a new resistor to put in and call it a done deal. One resistor I'd like to find though is a 7.5K 7W green plate load resistor(R186). Its in the plate of the 8AL9 and I dont like the way it looks. Its also in a terrible spot all the way up in front of the chassis under the CRT. Basically impossible access without TV dissassembly.

I do give good credit to GE for one thing, they made a removable service plate under the chassis so I can solder under the board. There are alot of reinforcement ribs though so the probability of the part you need to replace being under a rib is quite high. I can be a hack tech and use a pair of snips to cut the rib out of my way so I can work, but I dont like doing things that way. This is a neat set and need to keep it working for a few more hours.
__________________
I tolerate the present by living in the past...
To see drh4683's photo page, click here
To see drh4683's youtube page, click here
Reply With Quote
  #2  
Old 06-23-2008, 08:16 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Doug,

Glad to hear you got the set fixed. I'll check my stock - I probably have the 7W, 7.5K resistor in my stock of stuff. Those resistors are tough - I've seen them absolutely white from overload, but still check within 5% tolerance. Corning made them - basically metal film on a ceramic core with bronze crimps on the ends. I'll check tomorrow - short day for me, as I'm volunteering up some time at Bible School for the kids.

A-HEM..you owe us some pix - or a link when you post them to your gallery.

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #3  
Old 06-24-2008, 06:03 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by drh4683 View Post
Well,
One resistor I'd like to find though is a 7.5K 7W green plate load resistor(R186).
Doug,

I gotcha one - it'll be on it's way in the morning. Spankin new one - green and all.....

Spent the day sorting through some stuff, hoping to find your resistor. Need any Belfuses? I could fill a shoebox with them - and I even have the sockets! Dad sure had some great stuff, the bulk of which is too new for 90% of the forum. Some day I'll get it all cataloged.

Your resistor is on it's way in the AM - I still have your address in Batavia.

Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
  #4  
Old 06-24-2008, 08:02 PM
drh4683's Avatar
drh4683 drh4683 is offline
VideoKarma Member
 
Join Date: Jan 2003
Location: Chicago, IL
Posts: 2,094
Brian,

thanks a million for all your help. I really appriciate it. Its always good to have a nice stock of belfuses! Ive got a few myself. I have an old library card catalog cabinet that I keep alot of small compnents in. One of those drawers is belfuses of all sorts!

Once I get the new resistors installed, I'll get some photos of this set posted. I got this set back in february. Its been sitting on my "off to the side" tv bench with the back off since then awaiting the repairs! So many other projects took presedence. Im glad I finally made it important get to this one.
thanks again
__________________
I tolerate the present by living in the past...
To see drh4683's photo page, click here
To see drh4683's youtube page, click here
Reply With Quote
  #5  
Old 06-26-2008, 08:16 PM
drh4683's Avatar
drh4683 drh4683 is offline
VideoKarma Member
 
Join Date: Jan 2003
Location: Chicago, IL
Posts: 2,094
There are yet more problems to deal with now. I noticed that there is quite a bit of corona discharge around the HV lead. So I decided to check the HV and its running high at 25KV. Supposed to be 22KV and HV control does absolutly nothing. This is one of those mint condition all original TVs that will have one problem after another. These are the worst ones. I'll be looking into the problem later on.
__________________
I tolerate the present by living in the past...
To see drh4683's photo page, click here
To see drh4683's youtube page, click here
Reply With Quote
Audiokarma
  #6  
Old 06-26-2008, 10:11 PM
Findm-Keepm's Avatar
Findm-Keepm Findm-Keepm is offline
Followin' the Rules...
 
Join Date: Jun 2007
Posts: 2,857
Quote:
Originally Posted by drh4683 View Post
I noticed that there is quite a bit of corona discharge around the HV lead.
Doug,

Check C278 - GE had a bulletin about this very problem - corona discharge (arcing), too much HV, and short damper tube life. C278 is part of the focus tracking assembly, but can be replaced separately if the two 430K resistors check within tolerance. GE advises to replace the whole assembly if any sign of arcing has occured (carbon traces, bunr marks, etc). Real common problem on these sets.

Two other caveats, based on Dad's handwritten notes - R251, a 39K resistor, will go out of tolerance (high) and cause problems. It ties the horizontal osc/AFC circuit to the damper. Also check C268, a pulse coupling cap (.005uF) that feeds the HV adjust circuit. They tend to open/change value - if it shorts, you'll lose color keying or have color sync issues. Open, no pulse to rectify for HV regulation.

Hope these tips help, still digging. Dummy me passed on the GE service literature from another shop/GE service center that closed after 35+ years. But hey, I DID get the GE parts....

And according to the post office, your resistor has left Norfolk:

Your item was processed and left our NORFOLK, VA 23501 facility on June 25, 2008.


Cheers,
__________________
Brian
USN RET 22YRS (Avionics/Cal)
CET-Consumer Repair and Avionics ('88)
"Capacitor Cosmetologist since '79"

When fuses go to work, they quit!
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:44 AM.



Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
©Copyright 2012 VideoKarma.org, All rights reserved.