![]() |
|
|
|
#1
|
||||
|
||||
|
Have you recapped that set? Checked the tubes?
It would seem that you might have a leaky capacitor, or perhaps a resistor or two that have drifted in value. Does the HOT plate get red? I laid my hands on a Sams for a slightly later model Zenith using a 6SN7 for horiz osc/disch and a 6BQ6 for HOT. THe waveform they show is a reasonably pure sawtooth, and not one where the top is clipped the way yours is. Checking the operating voltages against design figures may uncover the culprit. The screen voltage at the HOT could be low. Also the plate resistor in the preceding stage could have changed in value. Also check the amount of developed negative voltage there is on the HOT control grid. The Sams I have shows -15 volts for control and 150V for screen. I feel fairly certain that your 6BG6 should operate at voltages not far from these.... |
|
#2
|
|||
|
|||
|
Every cap was replaced, as well as every out-of-tolerance resistor. I'll take some voltage measurements and post them tomorrow. Thanks for commenting on my post.
|
|
#3
|
||||
|
||||
|
Does the raster show adequate width before the HV starts going down? Bear in mind that as the accelerating voltage goes down the raster size will lose brightness, focus--and become larger.
If your voltages all jibe then my gut is telling me that the HOT is played out, or that perhaps the flyback has issues.... |
|
#4
|
|||
|
|||
|
Flyback is a brand new old stock FLY-51. 6BG6GA is NOS. Here are some voltage readings:
Horizontal discharge 6SN7: Pin 2 anode: expected +65v, actual +37v; Pin 1 grid: expected -33v, actual -30v Horizontal output NOS 6BG6GA (tube plugged in, anode NOT connected to flyback): Pin 8 screen grid: expected 255v actual 267v; pin 5 control grid: -7v expected -27v actual; pin 3 cathode: +14v expected +2v actual All caps replaced, and I have triple-checked accuracy. All resistors in that section replaced, again, have rechecked accuracy. The biggest variations seem to be the anode of the horizontal discharge, and the control grid of the horizontal output. Does all of this suggest anything? Thanks! |
|
#5
|
|||
|
|||
|
Re: "Bear in mind that as the accelerating voltage goes down the raster size will lose brightness, focus--and become larger." Yes, that is what happens as I turn the horizontal drive clockwise from start.
|
| Audiokarma |
|
#6
|
||||
|
||||
|
The voltage readings on the HOT tend to point the finger at excessive drive.
This would jibe with the waveforms you show the more I think about it. The clipping at the top suggests diode action of the control grid caused by its being driven well into conduction. There is some of this happening to a degree in normal operation, as that is how the HOT develops the negative bias that keeps the cathode current in check. In cases of horizontal oscillator failure the HOT would melt down completely. But it would seem that the reverse is happening here, as your cathode voltage reading and the control grid negative reading reflects little current flow, as if the tube is conducting only during a very small part of the waveform cycle. If that be the case then one would think that the width of the raster would be affected, and that one side of the raster would actually show a brighter edge, reflecting the beam lingering there during the HOT's cutoff. Just the same such condition would cause lower output from the HOT, as it is only conducting for short bursts. Attempts to further increase drive will only make matters worse.It seems to me that you need to be going in the other direction, if possible. ![]() Do you actually have a video program source or a test pattern in your testing? Or are you just working with a white raster or snow? |
|
#7
|
|||
|
|||
|
Tonight I will input a test pattern and re-do the voltage measurements. Is the low voltage on pin 2 of the 6sn7 a problem? Should I reduce the value of the 560k plate resistor to increase the voltage? Would it be helpful if I sent the schematic? If so, can you send me a personal message with your email address? Thanks!
|
![]() |
| Thread Tools | |
| Display Modes | |
|
|